Publications associées à Spot welding

Experimental Investigation of the Inelastic Cyclic Behavior of Concrete-Filled Double-Skin Tubular Beam-Columns with Corrugated Inner Skins and Ultrahigh-Strength Corner Tubes

This paper presents the experimental results from nine full-scale concrete-filled double-skin tubular (CFDST) beam-columns. The test specimens exploited two fabrication strategies, featuring either hollow steel inner skins with corrugated geometry or ultra ...

ASCE-AMER SOC CIVIL ENGINEERS2022

Reliability analysis of welded stud shear connectors on simply-supported bridge girders

Scott Walbridge, Matthew James Sjaarda

This paper examines the reliability of welded stud shear connectors for steel-concrete composite bridge girders. A finite element model of a simply-supported bridge was created featuring link connector elements representing the shear studs between beam and ...

CANADIAN SCIENCE PUBLISHING2021

Performance of Embedded Bolt Shear Connectors

Scott Walbridge, Matthew James Sjaarda

A laboratory research program carried out at the University of Waterloo featured the testing of three large-scale steel-concrete composite beam specimens with embedded bolt shear connectors. A detailed assessment of the connector performance was made, faci ...

TAYLOR & FRANCIS LTD2020

Diffractive optical elements in single crystal diamond

Niels Quack, Marcell Kristof Kiss

We demonstrate the design, fabrication, and experimental characterization of near-field binary phase transmission diffractive optical elements (DOEs) in single crystal diamond. Top-hat and arbitrary pattern DOE beam shapers were numerically optimized using ...

OPTICAL SOC AMER2020

Healing cracks in selective laser melting by 3D laser shock peening

Roland Logé, Jamasp Jhabvala, Christian Leinenbach, Nikola Kalentics, Navid Sohrabi, Hossein Ghasemi Tabasi, Andreas Burn

Selective Laser Melting (SLM) of Ni-based superalloys such as CM247LC is prone to weld-cracking. This paper investigates how to suppress cracks by repeatedly applying Laser Shock Peening (LSP) during the building phase of SLM. Samples made of CM247LC were ...

ELSEVIER2019

Residual stresses of friction melt bonded aluminum/steel joints determined by neutron diffraction

Jean-Marie Drezet

Near interfacial residual stresses are investigated in a joint composed of aluminum alloy and dual phase steel. A small step neutron diffraction scan was initially performed to determine the weld interface position along the measured transverse cross secti ...

ELSEVIER SCIENCE SA2019

Recommendations for Improved Welding Procedures for Thick Steel Plates Through Thermo-Mechanical Analysis

Dimitrios Lignos

Welding of steel plates is accompanied by residual stresses that increase as the constraint provided by the welded components becomes greater. Consequently, crack initiation has been reported after welding thick plates due to the high residual stresses dev ...

2019

Interface microstructure formation of dissimilar Fe/Fe-Mn-C steel RSW joints

Léa Deillon

An experiment was developed to simulate the interface between liquid high manganese carbon steel and solid ultra-low alloyed steel in a thermal gradient, corresponding to the nugget/sheet interface of resistance spot welds. Despite the large difference in ...

Elsevier Science Sa2018

Microstructural evolution and mechanical property development with nickel addition in low-carbon weld butt joints

Roland Logé, Cyril Cayron, Gaojun Mao, Rui Cao

Four metal powder flux-cored wires with added nickel (Ni) were designed to systematically investigate how Ni influences the microstructure and toughness in low-carbon bainitic weld metals (WMs). The microstructure was safely predicted by utilizing reasonab ...

2018

Stress intensity factors for axial semi-elliptical surface cracks and embedded elliptical cracks at longitudinal butt welded joints of steel-lined pressure tunnels and shafts considering weld shape

Anton Schleiss, Pedro Filipe De Almeida Manso, Alexandre Jean Pachoud

When for steel liners of pressure tunnels and shafts high-strength steels are used, welded joints are subject to the risk of hydrogen induced cold-cracking in the base material. Longitudinal butt welded joints are critical regions as they are loaded transv ...

Elsevier2017