Cours
MSE-735: Scanning and Analytical Transmission Electron Microscopy
Résumé
This intensive course discusses advanced TEM techniques such as: scanning TEM; analytical TEM using EELS and EDX; aberration corrected imaging; and image simulation. It is intended for researchers who have taken the introductory TEM course MSE-637 or who have a good background in conventional TEM.
Source officielle
Page Moodle
À propos de ce résultat
Cette page est générée automatiquement et peut contenir des informations qui ne sont pas correctes, complètes, à jour ou pertinentes par rapport à votre recherche. Il en va de même pour toutes les autres pages de ce site. Veillez à vérifier les informations auprès des sources officielles de l'EPFL.
Enseignants (4)
Marco Cantoni
1982-1988, Diploma course in Experimental Physics (certificate, 28.10.88)ETHZ Faculty IX MATHEMATICS and PHYSICS, Diploma Thesis: "Abweichungen von der ikosaedrischen Symmetrie in Al-Cu-Li Quasikristallen", Advisor: Prof. H.-U. Nissen 1989-1993, Ph.D. in Experimental Physics (certificate, 23.8.94) ETHZ Physics Department, Laboratory of Solid State Physics, Ph. D. Thesis No. 10421, Title: "Elektronenmikroskopische Untersuchung der Realkristallstruktur epitaktischer Schichten von Supraleitern des Typs SEBa2Cu3O7-x auf (100)-SrTiO3" Advisors: Prof. H.R. Ott, Prof. H. U. Nissen. 1994-1996,ETH Zürich,Material Science Department, Non-Metallic Materials, Prof. L. Gauckler: Microstructure characterisation of high-tech ceramic materials by means of SEM, TEM and atomic force microscopy: superconductor thick films (Bi-2212 on Ag) and solid oxide fuel cells (ZrO2, CeO2). 1996-1998, National Institute for Research in Inorganic Materials NIRIM, Japan Group for Special Research, Prof. S. Horiuchi: TEM of Bi-2223/Ag Tapes, Application of Imaging Plates (IP) in High Voltage TEM, Cryo-Lorentz-TEM of Superconducting Materials (Observation of Flux-Lines) 1998-2000, Ecole polytechnique fédéral de Lausanne, EPFL-CIME Centre interdépartemental de microscopie électronique CIME, Prof. P.A. Buffat: Projet 125, PPO II (programme prioritaire optique): Characterization of materials and devices for optic and optoelectronic applications by electron microscopy. 2001-2003, Ecole polytechnique fédéral de Lausanne, EPFL STI IMX LCCeramics Laboratory, Prof. Nava Setter Characterisation of ferroelectric materials, transmission electron microscopy of relaxor ferroelectric materials 2004, University of Geneva, Physics Department, Condensed matter Physics Group of Prof. R. Flükiger, TEM of Multifilament Nb3Sn superconducting wires, in collaboration with EPFL-CIME Since 1.11.04, EPFL-SB-CIME
Emad Oveisi
Dr Emad Oveisi is a senior scientist at the Interdisciplinary Centre for Electron Microscopy (CIME), EPFL.
Emad received a BSc in Metallurgy and Materials Engineering (2005) and an MSc in Materials Science (2008) both from the University of Tehran (Iran). He graduated with a PhD in Materials Science and Engineering at EPFL in 2014 for a thesis on the "Three-Dimensional STEM Imaging of Dislocations" under the direction of Prof. Cécile Hébert. The PhD thesis at the Electron Spectrometry and Microscopy Laboratory (LSME), served as an introduction to many of the advanced microscopy techniques that have proven to be a platform for his research career. A post-doctoral research at the centre for electron microscopy gave him the opportunity to peruse a cutting-edge research on one of the most modern aberration-corrected transmission electron microscopes.Since the inauguration of the Energypolis campus of EPFL in Sion, he has been the manager and reference scientist of the electron microscopy platform of EPFL-Valais, working with 9 research groups and more than 200 researchers. In addition to this core responsibility, he provides advanced microscopy consulting and service to EPFL scientists and assist their research to the highest level possible.
Emad Oveisi’s research focuses on the application and development of novel electron microscopy techniques, with emphasis on 3D imaging of crystal defects, as well as the precision measurement of materials properties using aberration-corrected S/TEM. In 2018, he received the prestigious Microscopy Innovation Award for inventing “Single-shot three-dimensional electron imaging”, a novel technique that enables 3D imaging of in situ dynamics.
In 2016 Emad was elected as an interim representative for the scientific staff ("corps intermédiaire") to the Council of the Institute of Chemistry (ISIC). Since 2019, he is a member of EPFL Teachers’ Council (CCE) and has been elected as one of its four bureau members. This role allows him to be exposed to new ideas and pedagogical challenges, as well being involved in discussions with the Vice Presidency of Education (VPE) and other teaching organisations for defining teaching strategies at the EPFL.
Cours associés (45)
MSE-352: Introduction to microscopy + Laboratory work
Ce cours d'introduction à la microscopie a pour but de donner un apperçu des différentes techniques d'analyse de la microstructure et de la composition des matériaux, en particulier celles liées aux m
MSE-450: Electron microscopy: advanced methods
With this course, the student will learn advanced methods in transmission electron microscopy, especially what is the electron optical setup involved in the acquisition, and how to interpret the data.
MSE-637(b): Transmission electron microscopy and diffraction (b)
This intensive course is intended for researchers who envisage using transmission electron microscopy to study materials samples or to help them interpret TEM data in publications. It presents basics
PHYS-405: Experimental methods in physics
The course's objectivs are: Learning several advenced methods in experimental physics, and critical reading of experimental papers.
CH-633: Advanced Solid State and Surface Characterization
State-of-the-art surface/thin film characterization methods of polycrystalline/nano/amorphous materials. Selected topics from thin film X-ray diffraction (GIWAXS, GISAXS, PDF), electronic and optical
MOOCs associés (9)
Micro and Nanofabrication (MEMS)
Learn the fundamentals of microfabrication and nanofabrication by using the most effective techniques in a cleanroom environment.
Microstructure Fabrication Technologies I
Learn the fundamentals of microfabrication and nanofabrication by using the most effective techniques in a cleanroom environment.
Micro and Nanofabrication (MEMS)
Learn the fundamentals of microfabrication and nanofabrication by using the most effective techniques in a cleanroom environment.