Publications de Jürgen Einpaul

Measurements of internal cracking in punching test slabs without shear reinforcement

Aurelio Muttoni, Miguel Fernández Ruiz, Jürgen Einpaul

Advancing the knowledge about the punching behaviour of flat slabs has been held back by the fact that only indirect measurements of the internal failure mechanism have typically been available. In this paper, a novel experimental approach for tracking the ...

2018

Performance of punching shear reinforcement under gravity loading: Influence of type and detailing

Aurelio Muttoni, Miguel Fernández Ruiz, Fabio Brantschen, Jürgen Einpaul

The performance of 11 different shear reinforcement systems against punching of inner slab-column connections under gravity loading was compared on the basis of experiments on 12 full-scale specimens, 8 of them newly reported. The slab geometry and flexura ...

ACI Structural Journal2016

Punching shear capacity of continuous slabs

Aurelio Muttoni, Miguel Fernández Ruiz, Jürgen Einpaul

Provisions for punching shear design of reinforced concrete slabs are usually calibrated on the basis of results from tests on isolated specimens that simulate the slab zone within the points of contraflexure around a column. However, the punching behavior ...

ACI Structural Journal2016

Study on Influence of Column Size and Slab Slenderness on Punching Strength

Aurelio Muttoni, Miguel Fernández Ruiz, Jürgen Einpaul

This paper presents the results of a systematic experimental campaign consisting of 13 symmetric punching tests on interior slab-column connections. The study focuses on the influence of varying the size of the supported area and the slenderness of the sla ...

ACI Structural Journal2016

Punching strength of continuous flat slabs

Jürgen Einpaul

Reinforced concrete slabs with uniform thickness are common in residential and commercial buildings but can also be found in other types of structures. Such slabs are susceptible to punching shear failures, where a supporting column penetrates through the ...

EPFL2016

Experimental investigation of soil - structure interaction for transition slabs of integral bridges

Aurelio Muttoni, Olivier Burdet, Jürgen Einpaul

This paper presents the results of an experimental test series on the soil-structure-pavement interaction in the vicinity of the transition slab at the end of an integral bridge. The main function of transition slabs is to ease the transition between the b ...

Structural Concrete2015

Influence of moment redistribution and compressive membrane action on punching strength of flat slabs

Aurelio Muttoni, Miguel Fernández Ruiz, Jürgen Einpaul

The punching shear strength of interior column connections of flat slabs has traditionally been investigated with isolated test specimens subjected exclusively to hogging bending moments. However, the behavior of such specimens is different from that of ac ...

Engineering structures2015

On the efficiency of flat slabs strengthening against punching using externally bonded fibre reinforced polymers

Aurelio Muttoni, Miguel Fernández Ruiz, Jürgen Einpaul, António Manuel Pinho Ramos, Duarte Miguel Viúla Faria

One possibility for strengthening existing flat slabs consists on gluing fibre reinforced polymers (FRPs) at the concrete surface. When applied on top of slab–column connections, this technique allows increasing the flexural stiffness and strength of the s ...

Construction and Building Materials2014

Punching resistance and flexural behaviour of continuous flat slabs

Aurelio Muttoni, Miguel Fernández Ruiz, Jürgen Einpaul

The punching resistance of actual reinforced concrete flat slabs is potentially influenced by the compressive membrane action, which may significantly increase their resistance compared to isolated laboratory specimens. However, design codes have been deve ...

Proc. of the 10th fib International PhD Symposium in Civil Engineering, Quebec2014

Punching strength of actual two-way slabs

Aurelio Muttoni, Miguel Fernández Ruiz, Jürgen Einpaul

Many building codes rely on empirical formulations with respect to the punching shear design provisions. Such empirical equations are typically calibrated on the basis of laboratory tests performed on simplified geometries (usually isolated specimens) with ...

4th fib Congress, Mumbai2014