Microstructure of single crystal Ni-based superalloys during blade manufacturing process and creep deformation

The aim of the thesis is to obtain more understanding about the influence of plastic deformation on the microstructural changes observed in single crystal (SX) Ni-based superalloys using diffraction techniques. This work was organised around two main problematics: (1) rafting in turbine blades after the manufacturing process and (2) rafting and mosaicity evolution in two SX alloys with different composition during creep deformation. SX Ni-based superalloys are first choice materials for turbine blade application in land-based gas turbines and aero-engines. Superior mechanical properties of these materials at high temperatures are achieved due to the optimisation of the alloying composition and the microstructure. SX Ni-based superalloy turbine blades solidify by dendritic solidification with dendrites aligned along the directions of lowest Young modulus (interdendritic spacing around 300μm). At the end of the manufacturing process, the microstructure consists of high volume fraction of cubic γ’ precipitates (around 500nm) coherently embedded in the γ matrix. However specific parts of engine-ready turbine blades exhibit directionally coarsened γ’ precipitates in a preferred direction (rafting) without the influence of an applied load. It is of prime importance to understand the origin of rafting prior to the introduction of the blades in the engine since rafting can alter the mechanical properties of the alloy. Chemical segregations and the introduction of plastic deformation prior to thermal treatments were identified as potential driving force for rafting during load-free high temperature annealing. Most of the SX Ni-based superalloys used in the current blade production in Alstom contain significant amount of refractory elements which are expensive and increase the density of the alloy. To answer the demand of cheaper and lighter components, Alstom launched a development program to design novel SX superalloys. One of these projects led to the production of a Re-free superalloy, so-called MD2. Extensive mechanical investigations on MD2 are on-going and compared to the behaviour of the MK4HC alloy (3wt% Re) currently used in turbine blade production. One of the major differences in terms of mechanical properties between Re-containing and Re-free SX alloys is the faster kinetics of coarsening and rafting during creep deformation at high temperature in the latter alloys. It prevented so far their application in the hottest areas in gas turbines. It is therefore of utmost importance to acquire more knowledge about the mechanisms associated with the microstructure evolution during creep of the new MD2 SX alloy in comparison with the MK4HC alloy. The evolution of the lattice parameter misfit in different directions with respect to the applied load during creep deformation was associated with the evolution of the microstructure from cubic to elongated γ’ precipitates It could be shown that rafting occurs after the cooling stage following the solution heat treatment (SHT) during the manufacturing of the blade with investigations of the microstructure. The influence of chemical segregations on rafting was excluded with the investigation of the blade alloy composition in different parts of the blade cooled from the SHT and diffraction measurements in stress-relieved combs prepared from the same blade. The formation of a rafted microstructure during the manufacturing process was associated with the formation of plastic strains during cooling after the SHT. This was confirmed after gathering results from investigations of the microstructure, simulation of the cooling stage and neutron diffraction measurements on the blade. The investigations of the microstructure performed on the engine-ready blade revealed an inversion of the γ’ raft orientation below (parallel to [001]) and above the platform of the blade (perpendicular to [001]). This was attributed to an inversion of the sign of residual strain between the previously mentioned positions as revealed by neutron diffraction measurements performed along the airfoil of the blade cooled after the SHT. Microscopy also showed that the rafted microstructure was more pronounced below the platform (long γ’ rafts) than above the platform (shorter γ’ rafts with retained cubic precipitates). The concept of the threshold plastic strain necessary to induce rafting during annealing subsequent to plastic deformation was used to describe the difference in rafted microstructure. It is suggested that plastic strains largely exceed the threshold below the platform leading to fully formed rafted microstructure. On the other side, plastic strains of the order to the threshold strain are suggested above the platform in order to explain the partially formed rafted microstructure Neutron diffraction measurements revealed that the lattice parameter misfit was larger in the MK4HC than in the MD2 alloy at 20°C in the unloaded state. The larger misfit in the MK4HC alloy was attributed to the larger concentration of elements dissolving in the γ phase and to the presence of Re. During creep deformation, coherency stresses are relieved at the γ/γ’ interface in the γ channels perpendicular to the applied load by dislocations. On the other hand, dislocations increase the internal stress at the γ/γ’ interface in the γ channels parallel to the applied load. This leads to the rafting of the γ’ precipitates perpendicular to the applied load. This was observed in the MK4HC. The absence of clear misfit evolution in the MD2 alloy was attributed to the anomalous microstructure at the beginning of the creep deformation. The mosaicity of the MK4HC and MD2 alloys revealed crystallographic misorientation between neighbouring dendrites up to 0.5°. The misorientation was associated with the presence of dislocations in the regions between the dendrites formed during the dendritic solidification of the alloys from existing work. It was shown that the composition of the SX alloys and short periods at high temperature in the unloaded state had only little influence on the misorientation between neighbouring dendrites. Upon creep loading to 180MPa, the mosaicity markedly changed in the two SX alloys independent of the creep temperature. In particular, the number of single misoriented domains measured by X-ray diffraction decreased. This was attributed to the fast propagation of the dislocations present in the interdendritic structure inducing a rotation of the individual dendrites. During creep deformation, the mosaicity increased as visible from the broadening of the maximum spread in misorientation. The formation of inhomogeneous plastic strain fields in the γ/γ’ microstructure is believed to create new mosaic blocks in the dendritic structure of the alloys leading to the observed broadening of the mosaicity. The influence of plastic deformation on the evolution of the mosaicity was demonstrated. The mosaicity significantly changed during creep of the MD2 at 1050°C/180MPa and 1000°C/180MPa whereas no significant evolution could be measured during creep at 950°C/180MPa. This was attributed to a temperature dependence of the yield strength of the MD2 alloy. It therefore induces difference in dislocation propagation at 950°C compared to 1050°C and 1000°C which retards the broadening of the mosaicity during creep at 950°C. Furthermore, the mosaicity formed during creep deformation was retained upon unloading and cooling of the SX samples to room temperature.

On the relationship between the microstructure and the mechanical properties of an ODS ferritic/martensitic steel

Amuthan Ramar

In the quest of materials for the first wall of the future fusion reactor, it has been shown that oxide dispersion strengthened (ODS) ferritic / martensitic (F/M) steels appear to be promising candidates. The inherent good mechanical properties supported by a good thermal conductivity, swelling resistance and low radiation damage accumulation of the base material, such as EUROFER97, are further enhanced by the presence of a fine dispersion of nanometric oxide particles. They would allow in principle for a higher operating temperature of the fusion reactor, above 550°C, which improves its thermal efficiency. In effect, their strength remains higher than the base material at high temperatures. There are however limitations to their application in the reactor, which relate to the intimate link between the microstructure and the mechanical properties. These limitations, such as an increased ductile to brittle transition temperature above room temperature relative to the base material, come directly from the role played by the oxide particles but also from their indirect impact on the overall microstructure, stemming from the procedure of elaboration of these materials. In addition, there is a lack of knowledge on their response to irradiation, which, even though it appears to be promising with a reduced irradiation induced hardening, is not very well understood. In this work we have developed and evaluated ferritic/martensitic steel, EUROFER97, strengthened by a dispersion of yttria particles. (1) The powder metallurgical process used to obtain it was optimized, (2) the basic mechanisms of hardening were identified and (3) the impact of irradiation on its microstructure and mechanical properties were investigated. In order to understand the behaviour of this class of material other oxide dispersion strengthened (ODS) ferritic/martensitic steels based on EUROFER97 and model alloys were also investigated. For the elaboration of the ODS steel the powders of atomized EUROFER97 and yttria are ball milled in a planetary ball mill and the material is compacted by hot isostatic pressing (HIP). The mechanical properties are evaluated by uniaxial tensile test, Charpy test and micro-indentation while the microstructure is investigated by optical microscopy, scanning electron microscopy and transmission electron microscopy. The focused ion beam (FIB) technique is also used. In the study of the ball milling it appears that the optimal time is 20 hours, as the X-ray peak broadening, crystallite size and hardness of the particles remain unchanged at longer times. Yttria nanoparticles clusters are no more detectable by X-ray after 2 hrs of milling, which is attributed here to their incorporation in the matrix, as opposed to dissolution in the matrix as is often suggested in the open literature. HR-TEM performed on the yttria particles before and after incorporation in the steel by ball milling shows that the yttria maintain its bcc equilibrium structure throughout the process. This could suggest that they are not dissolved during ball milling. We have clarified this point by a cross sectional examination of the EUROFER97 ball milled particles with 0.3wt% of yttria in an FIB. By X-ray EDS analysis it shows nanometric regions reach in yttrium and oxygen, which are the yttria particles embedded in the EUROFER97 particles, proving that they are not dissolved by ball milling. The mechanism at the origin of the alloy compaction during HIP was elaborated. The alloy compaction was done through HIPing at 1150°C for 2.5 hrs at a pressure of 190 MPa. This condition is shown to provide the highest bulk density, to a value close to 99.9%. In the optimization process, it is found that temperature plays a larger role than pressure for alloy compaction. The compaction appears to be mainly due to diffusion. Also, it appears that the ball milled particle size plays a major role in the alloy compaction. It is shown that smaller particles size induces better compaction, provided that the densification proceeds through diffusion flow. This further suggests to terminate the ball milling process by 20 hrs as the particles size reaches its minimum. The impact of the ball milling process on the mechanical properties was evaluated. EUROFER97 with and without ball milling, with and without oxide addition presents an average density around 99.8%. In the as received state, casted EUROFER97, atomized EUROFER97, ball milled EUROFER97 and ODS Yttria present microstructure morphology typical of tempered martensite, whereas ODS Ti presents a nano sized grain microstructure with an average grain size of 200 nm. Ball milling and HIPping does have a slight influence up to 400°C, due to the higher dislocation density induced by ball milling relative to casted EUROFER97. It becomes negligible above 400°C, since both casted and ball milled EUROFER97 present similar hardness and microstructure. In ODS Yttria, yttria presents an average particle size of 25 nm. In ODS Ti, Y-Ti-O presents an average particle size of 7 nm. In the following the identification of the hardening mechanisms in ODS F/M steels. A new model was developed to quantify the collective hardening due to different obstacles, assuming that they provide independent hardening mechanisms. The model helped identifying the dominating source of hardening in ODS F/M steels. The base of the model is the dispersion barrier strengthening model, which is given by Δσsparticle or defects = Mαμb(Nd)1/2 for the hardening due small defects or oxide particles and is given by Δσd-d = Mαμb(ρ)1/2 for the hardening due to dislocations. In this approximation, the total hardening is then given by Δσtotal = {(Δσd-d)2 + (Δσparticle or defects)2}1/2 . The model is used to explain the hardening due to oxides, dislocations and irradiation induced defects. It appears that dispersed oxides is dominating hardness up to 800°C, while following a heat treatment at 1000°C it is the dislocations that then dominate the hardness. Deformation mechanisms were investigated using differential strain rate experiments. The activation parameters, i.e. the activation volume and activation energy, were calculated. It appears that there is a decrease in the activation volume from room temperature to 400°C, which is less than 3%. At about 500°C there is a sudden drop in the activation volume that reaches a minimum at 600°C. With further increase in temperature, there is a significant raise in the activation volume. This abrupt decrease between 400°C and 600°C hints at a change in dislocation-rate controlling mechanism, marking two regimes, a low temperature one and a high temperature one. In situ TEM observations show that at low temperature the deformation is mainly due to the formation of the Orowan loops around the particle. At high temperature the activation energy is about 3.4 eV for ODS, whereas it is 1.3 eV for EUROFER97. The calculated activation energy corresponds well to the one of dislocation climb mechanism. This indicates that at high temperature the yttria particles could be overcome by climb, while at low temperature they are overcome by the Orowan mechanism. The peculiar response of the yield stress to irradiation for this class of material was rationalized using the total hardening model we developed. At a dose of 2 dpa, irradiation induced defects are higher in number density than the dispersed yttria particles, which although they are weaker than the yttria particles they can explain the significant hardening observed in the material. Conversely, the shallow impact of irradiation on ODS F/M steels at low doses, relative to base F/M steels, is explained by the fact that the amount of dispersoid is found to be higher than the density of irradiation induced defects.

EPFL2008

Precipitation in the high strength AA7449 aluminium alloy

Patrick Schloth

Al-Zn-Mg(-Cu) (AA7xxx) alloys are widely used structural materials owing to their excellent mechanical properties and low corrosion susceptibility. The high strength of these materials is obtained by the formation of secondary phases, e.g. precipitation. This present thesis aims at contributing to the understanding of the influence of precipitation in the high strength AA7449 alloy on the internal stress formation at different length scales. Two different cases are studied in this thesis. In the first case, the influence of precipitation during quench on macroscopic residual stresses (RS) is studied in an industrial 75 mm AA7449 thick plate. For some investigations the behaviour of the AA7449 alloy is compared with the medium strength AA7040 alloy. In the second case, the influence of different precipitation states on the internal strain formation is investigated at the microstructural length scale. For the first case, in situ small angle X-ray scattering evidenced that during quenching the heterogeneous eta phase forms at high temperatures in contrast to homogeneous GP(I) zones, which form at low temperatures. The eta formation is influenced by the cooling conditions but also by macrosegregation in the thick plate. Yet, the volume fraction of eta is very low and has a negligible effect on the macroscopic RS in thick plates. The homogeneous GP(I) zones form during quench with radii in the subnanometre range. Their formation is strongly influenced by excess vacancies. Fast cooling rates can lead to higher radius and volume fraction of GP(I) zones compared to slower cooling. The GP(I) zone formation increases the yield strength during quench and is responsible for the high RS in industrial thick plates. Therefore, the GP(I) zone formation during quench needs to be taken into account in macroscopic finite element (FE) residual stress simulations by using precipitation modelling. The GP(I) zone formation during quench is simulated by using a thermodynamic based Eulerian multi-class model. Therefore, a thermodynamic description for GP(I) zones is derived from reversion heat treatments by using the solubility product. The influence of excess vacancies is taken into account by adapted effective diffusion coefficients. This simplified approach allows reproducing reasonably well the measured GP(I) zone formation during rapid coolings. The coupling of the precipitation model with FE residual stress calculations (performed by the other PhD studentt) allows predicting very well the RS in two AA7449 thick plates. For the second case, in situ mechanical testing during tensile deformation using X-rays and neutrons evidence that the presence of different precipitate types change the internal strain formation in the aluminium matrix at the microstructural length scale. The presence of small GP(I) zones leads to an internal strain formation that is dominated by the intergranular strains of the aluminium matrix. When large eta precipitates are embedded in the aluminium matrix the interphase strains clearly dominate the internal strain formation. Further, it is shown that the eta phase has a higher elastic modulus than the aluminium matrix and shows an anisotropic behaviour during elastic and plastic deformation. In addition, it is pointed out that the internal strain formation at the microstructural length scale can have a significant effect on macroscopic RS measurements performed by XRD when the plastically deformed sample contains eta' and eta.

EPFL2015

Constitutive behavior and fracture properties of tempered martensitic steels for nuclear applications

Raul Alejandro Bonadé

In this study, the tensile and fracture properties and the microstructure of the reduced-activation tempered martensitic steel Eurofer97 have been investigated. This technical alloy is a 9%Cr steel developed within the European fusion material research program. To a lesser extend, the plastic flow properties of a equiaxed ferritic Fe9%Cr model alloy were also studied for comparison with those of the tempered martensitic structure. The main objectives of this work are described hereafter: to correlate the microstructural features with the plastic flow properties measured by the tensile tests for both the Eurofer97 steel and the model alloy. The correlation established should be reflected in a physically-based model of plastic flow. to study the fracture properties of the Eurofer97 steel in details in the lower ductile-to-brittle transition region. to calculate with finite element modeling the stress fields at the crack tip. This information is further used in conjunction with a local approach model for quasi-cleavage to reconstruct the fracture toughness-temperature curve. Tensile tests were carried out at different imposed nominal strain rate at several temperatures from 77K up to 473K, on both the Eurofer97 steel and the Fe9%Cr model alloy. The temperature dependence of the yield stress was precisely determined. As expected for body-centered cubic (BCC) materials, a strong increase of the yield stress by decreasing temperature, below 200 K, was observed. At higher temperatures, the temperature dependence of the yield stress was found much weaker, being associated with the temperature dependence of the shear modulus. Efforts were made to analyze in details the post-yield behavior (strain-hardening) as a function of temperature. The post-yield behavior was modeled using the Kocks phenomenological model based on the competition of storage and annihilation of dislocations. While this model was originally developed for face-centered cubic (FCC) metals where the rate-controlling mechanism of dislocation motion is the dislocation-dislocation interaction, we used is model in the high temperature domain (T>200K) of BCC materials, to model the strain-hardening evolution of the Eurofer97 steel and the model alloy. The values obtained for the key parameters of the model, namely the dislocation mean free path and annihilation coefficient, were found consistent with the microstructural features. The parameters temperature-dependence observed was also consistent with the physics of two basic mechanisms of dislocation storage and annihilation (dynamical recovery). For the low temperature domain, the strain-hardening model was modified to account for the strong Peierls lattice friction, based on an original idea of Rauch. Transmission electron microscopy observations were done to characterize the undeformed microstructures and their evolution with strain. A clear correlation was established between the stress-dependence of the strain-hardening and the microstructures. Fracture toughness tests on the Eurofer97 steel were performed with 0.2T C(T) and 0.4T C(T) specimens in the lower transition. Five temperatures were selected at which many tests were repeated to determine the amplitude of the inherent scatter of quasi-cleavage. The temperature were chosen in such a way that the measure fracture toughness remain below 150 MPa m1/2, which correspond for the 0.4T C(T) at a M value larger than 70 at the highest temperature. Such a M value for 0.4T C(T) specimens is known to ensure enough constraint. An attempt to analyze the experimental data in the framework of the master-curve approach by following the ASTM E-1921 standard was done. It was clearly demonstrated that the assumed shape of the toughness-temperature curve as described in the ASTM E-1921 standard for the reactor pressure vessel steels is not adequate for the tempered martensitic Eurofer97 steel, which present a particularly steep transition. Our Eurofer97 fracture database was then compared to the existing one on another similar steel, the F82H. Differences in the amplitude of the scatter of both steels was found while the lower bound of the toughness-temperature curve, describing the 1% failure probability was shown to be the same. 2D finite element simulations of the compact tension specimens were performed at various temperatures using the constitutive laws determined previously. The stress field around the crack tip were calculated and used to determine a local criterion of quasi-cleavage. The criterion is defined by the attainment of a critical stress encompassing a critical area. The lower bound of the toughness-temperature curve was then successfully reconstructed by using this local criterion. Finally, the relationship between the critical area and the applied stress intensity factor for the C(T) specimen was shown to follow a power law whose coefficients are dependent on the real dimensions of the specimen. Such a relationship allows scaling the C(T) toughness data from one size to another in case of in-plane constraint loss.

EPFL2006