EXPERIMENTAL STUDY ON FLOW BOILING HEAT TRANSFER OF MULTIPORT TUBES WITH R245fa AND R1234ze(E)

This article presents an experimental study of upward flow boiling heat transfer in multiport tubes. Usually, multiport tubes are utilized horizontally in automotive and air-conditioning systems while here there is interest in vertical flow as part of a two-phase thermosyphon electronics cooling system. Experiments were carried out in a flat aluminum extruded multiport tube, which was composed of 7 parallel rectangular channels (1.1mm × 2.1mm) with a hydraulic diameter of 1.4 mm. Two refrigerants, R245fa and the new refrigerant R1234ze, the latter a new environmentally safe refrigerant proposed as a potential replacement for R134a, were tested. A new hot water heating technique that accounts for either uniform or non-uniform local heat flux distribution along the channel, particularly for exploring high vapor qualities into the dryout region, was developed to obtain and reduce the data. Accordingly, heat transfer coefficients were measured locally for the entire range of vapor qualities starting from subcooled liquid to superheated vapor. Effects of heat flux, mass flux, vapor quality, and saturation temperature on flow boiling heat transfer in multiport tubes were considered. Finally, the experimental results were compared with some well-known correlations to evaluate the capabilities of existing prediction methods. The analysis completed so far shows that the three-zone model for slug flows works well for that subset of test results, utilizing the apparent surface roughness in place of the dryout thickness in the model, as has been previously done for silicon, stainless steel and copper microchannels with measured surface roughnesses. Notably, the non-dryout data were well predicted by the Cooper nucleate pool boiling correlation as in many other studies, although there is no proof that nucleate boiling is taking place except near the point of inception of boiling.

Two-Phase Heat Transfer Mechanisms within Plate Heat Exchangers

Raffaele Luca Amalfi

Plate heat exchangers are adopted in many domestic and industrial applications, such as ventilation, air conditioning, evaporation or condensation process, heat pumps and cooling of hydrodynamic circuits in engines. In the present thesis, an extensive experimental study to characterize thermal and hydraulic performance of a compact plate heat exchanger has been carried out and then follow up with proposition of new prediction methods for single-phase and evaporating flows in the plate¿s channels, in the form of general correlations that include large additional databases culled from the literature. Specifically, upward single-phase flow and flow boiling heat transfer of low pressure liquid refrigerants were investigated within a plate heat exchanger prototype fabricated with 1 mm pressing depth and chevron angle of 65°. High spatial and temporal resolution infrared measurements were implemented to obtain local (pixel-by-pixel) heat transfer coefficients and frictional pressure drops. Single-phase experiments were carried out for Reynolds numbers ranging from 34 to 1615 and Prandtl numbers from 4.9 until 6.5, and the associated effect of the main involved parameters on the thermal and hydraulic performance was analyzed in detail. Several of the most quoted prediction methods available in the literature were statistically evaluated against the present heat transfer and pressure drop database and a new models were proposed to predict mean and local thermal and hydraulic performance of the present compact plate heat exchanger. Two-phase experiments were carried out for mass fluxes ranging from 10 kgm-2s-1 to 85 kgm-2s-1, imposed heat fluxes from 225 Wm-2 to 4100 Wm-2, saturation temperatures from 19°C to 35°C and vapor qualities from 0.05 to 0.90. The heat transfer coefficient increased with mass flux, heat flux and saturation temperature (system pressure) whilst the frictional pressure drop rose with mass flux and vapor quality but decreased with saturation temperature. Based on local infrared measurements, a new correlation for predicting local frictional pressure gradient through the test section was proposed. Next, a wide experimental databank was culled from thirteen literature research studies, which investigated flow boiling heat transfer and two-phase frictional pressure drop within chevron plate heat exchangers. The database was first adopted to validate the predicted capabilities of 29 literature models, and then utilized to provide the new prediction methods to evaluate local heat transfer coefficients and frictional pressure gradient. These new models were developed from 1903 heat transfer and 1513 frictional pressure drop data points (3416 total) and were proved to work better over a very wide range of operating conditions, plate designs and fluids (including ammonia). The general flow boiling prediction methods have been programmed into a simulation code to analyze local thermal and hydraulic performance of the plate heat exchangers over a large range of test conditions. The simulation results were then validated against independent experimental database from literature, resulting in very good agreement between each other. The present simulation code represents a powerful tool to be used for practical applications by the thermal engineers in order to design and rate commercial plate heat exchangers.

EPFL2016

Contribution to the heat transfer analysis of natural and substitute refrigerants evaporated in a horizontal tube

Olivier Zürcher

The substitution of CFC refrigerants in refrigeration systems, heat pumps and organic Rankine cycles, requests a good knowledge of the heat transfer and pressure drop properties of substitute fluids. A contribution to this international effort is proposed with the study of two hydrofluorocarbon refrigerants (HFC-134a and the zeotropic mixture HFC-407C) and the study of the natural refrigerant ammonia. The HFCs have been experimentally tested on the first test rig developed in the Laboratory of Industrial Energy Systems (LENI) which was substantially modified to cope with ammonia, both in terms of safety requirements and operational conditions. The experimental test section is composed of two concentric tubes, with in tube evaporation of the refrigerant inside the inner tube of counter-current Annular water heating. A new database of the local heat transfer coefficients for the refrigerants HFC-134a, HFC-407C and ammonia together with pressure drop measurements has been collected and used to define and calibrate a new and more general heat transfer model. The two HFC refrigerants have been tested on the test rig developed by Kattan [36]; due to the chemical and the thermophysical properties of ammonia, a new test rig has been designed for the ammonia tests and a new calculation procedure based on the mean temperature measurement on the tube wall has been used. The experimental database covers evaporation tests on plain and on microfin tubes, and with nominal oil concentrations varying from 0 to 5 [%] (by wt.). Detailed modeling is concentrated on the tests on plain tube without oil. Each of the three refrigerants has been evaporated at 4[°C]. The other experimental conditions for the HFCs refrigerants were an inside tube diameter of 10.92[mm], a heat flux range of 2 – 5 [kW/m2] and three mass velocities of G = 100, 200, 300 [kg/(m2s)] visualized as Stratified-Wavy flows (G = 100[kg/(m2s)]), and mainly Annular for the higher mass velocities (G = 200, 300[kg/(m2s)]). The other global conditions for ammonia were an internal tube diameter of 14.00 [mm], a heat flux range of 5 – 70[kW/m2] and eleven mass velocities of G = 10,20,30,40,45,50,55,60,80,120,140[kg/(m2s)], corresponding to Stratified, Stratified-Wavy, Intermittent and Annular flow patterns; complementary tests, varying the mass velocity at constant vapor qualities (x = 20,50,80[%]), have been made in particular to better characterize boundaries between flow patterns. The flow patterns are visualized through glass sections at both ends of the 3.1 [m] long test tube. An extensive review of void fraction models with sensitivity analysis on the actual available flow pattern map has been made. From the 17 correlations reviewed, the models of Taitel-Dukler [71] and Rouhani [79] have been used. Other improvements to the threshold criteria of the Stratified-Wavy to Annular transition, lead to an accurate diabatic map to predict the flow patterns and their transition for very different families of fluids like HFC's and ammonia. A new approach in the prediction of two-phase flow heat transfer has been proposed through the study of each flow pattern separately, according to a new criterion defining the onset of nucleate boiling as a function of the critical convective heat transfer coefficient representative of the location where nucleate boiling might occur. A function based on a pseudo Biot number allows, from the mean heat flux around the tube periphery, to base the model on two different mean heat fluxes applied respectively to the parts of the perimeter in contact with the liquid and the vapor in stratified types of flow. Considering pure convective heat transfer, or mixed convective and nucleate heat transfer, this division allows the use of a common criterion to be applied to each flow pattern. The two-phase flow heat transfer coefficient has finally been obtained as a weighted mean function of the vapor and the liquid heat transfer coefficient with respect to their contact surface with the heated tube. Based on the database of refrigerants HFC-134a and ammonia, the standard deviation of the new heat transfer model is of σ = 27.9[%]. Even if the database showed that the flow conditions were close to, or in the turbulent to laminar flow transition, and even if the major part of the experimental points were purposely obtained close to the various flow pattern transitions, the new model showed very good agreement with the experimental database. Due to the precision of the new flow pattern map and the effectiveness of the onset on nucleate boiling criterion, this new heat transfer model accurately predicts the heat transfer conditions during evaporation. Finally, a new method to model separated flows is proposed, based on partial hydraulic diameters and a mean interface velocity.

EPFL2000

INFLUENCE OF THE SATURATION TEMPERATURE ON THE HEAT TRANSFER COEFFICIENT FOR FLOW BOILING INSIDE HORIZONTAL SMOOTH TUBES

Ricardo Lima, John Richard Thome

This article presents experimental results of heat transfer from two different studies [1, 2] for horizontal flow boiling inside smooth copper tubes with different refrigerants. The main goal of this study was to verify the influence of the saturation temperature on the heat transfer coefficient. The experimental tests were carried for refrigerants R-134a, R-22 and R-404A, at saturation temperatures ranging from 5 to 20°C for two tubes of 12.7 and 13.84 mm ID and three heat fluxes of 5, 7.5 and 17.5 kW/m2. The vapor quality ranged from 5 to 90% and the mass velocity was 300 kg/s.m2. Under these conditions the heat transfer coefficient shows an interesting trend: it behaves differently, in function of the saturation temperature, in the nucleate and convective boiling dominated regions. In the nucleate boiling dominated region the heat transfer coefficient increases with the saturation temperature. In the convective boiling dominated region this phenomenon is inverted, that is, the heat transfer coefficient decreases with the saturation temperature. This phenomenon was verified through the concept of the thermal resistance of the liquid thickness. Since the heat transfer coefficient is proportional to the inverse of the thermal resistance of the liquid film, it increases with decreasing saturation temperature. The transition between nucleate and convective boiling dominated regions, denominated by [1] as a local minimum of the heat transfer coefficient, was also clearly observed with all the refrigerants.