Infrared light management in high-efficiency silicon heterojunction and rear-passivated solar cells

Silicon heterojunction solar cells have record-high open-circuit voltages but suffer from reduced short-circuit currents due in large part to parasitic absorption in the amorphous silicon, transparent conductive oxide (TCO), and metal layers. We previously identified and quantified visible and ultraviolet parasitic absorption in heterojunctions; here, we extend the analysis to infrared light in heterojunction solar cells with efficiencies exceeding 20%. An extensive experimental investigation of the TCO layers indicates that the rear layer serves as a crucial electrical contact between amorphous silicon and the metal reflector. If very transparent and at least 150 nm thick, the rear TCO layer also maximizes infrared response. An optical model that combines a ray-tracing algorithm and a thin-film simulator reveals why: parallel-polarized light arriving at the rear surface at oblique incidence excites surface plasmons in the metal reflector, and this parasitic absorption in the metal can exceed the absorption in the TCO layer itself. Thick TCO layers-or dielectric layers, in rear-passivated diffused-junction silicon solar cells-reduce the penetration of the evanescent waves to the metal, thereby increasing internal reflectance at the rear surface. With an optimized rear TCO layer, the front TCO dominates the infrared losses in heterojunction solar cells. As its thickness and carrier density are constrained by anti-reflection and lateral conduction requirements, the front TCO can be improved only by increasing its electron mobility. Cell results attest to the power of TCO optimization: With a high-mobility front TCO and a 150-nm-thick, highly transparent rear ITO layer, we recently reported a 4-cm(2) silicon heterojunction solar cell with an active-area short-circuit current density of nearly 39 mA/cm(2) and a certified efficiency of over 22%. (C) 2013 American Institute of Physics. [http://dx.doi.org/10.1063/1.4772975]

Single molecule detection and fluorescence correlation spectroscopy on surfaces

Kai Hassler

In this thesis a new approach for single molecule detection and analysis is explored. This approach is based on the combination of two well established methods, fluorescence correlation spectroscopy (FCS) and total internal reflection fluorescence microscopy (TIRFM). In contrast to most existing fluorescence spectroscopy techniques, the subject of primary interest in FCS is not the fluorescence intensity itself but the random intensity fluctuation around the mean value. Intensity fluctuations are induced by thermal noise in a minute observation volume, which is in classical FCS the confocal volume of a confocal microscope. E.g. FCS is commonly utilized to investigate diffusion. In this case, diffusing fluorescent molecules entering or leaving the observation volume cause intensity fluctuations, which are analyzed by calculating the temporal autocorrelation of the observed signal. The autocorrelation is a measure for the self-similarity of a signal and contains information about the average fluctuation strength and duration. The confocal observation volume, i.e. the measurement volume that is actually seen by the detector is approximately given by the product of the optical transfer function with the fluorescence exciting intensity distribution of a focused laser beam. To achieve a high signal-to-background ratio a small observation volume is absolutely essential, first of all because the background from e.g. scattered light increases with the size of the observation volume. Second, a small volume assures for a small average number of fluorophores inside the observation volume and therefore for a high fluctuation amplitude i.e. FCS signal. This thesis proposes and discusses an alternative to confocal FCS specially conceived for measurements on surface-bound molecular systems, such as biological receptors or immobilized enzymes. In contrast to confocal FCS, fluorescence is excited within an evanescent field generated by total internal reflection (TIR) of a laser beam at the interface between a microscope coverslip and the sample. This is achieved by focusing the laser beam off-axis at the back focal plane of a high NA oil-immersion objective. The collimated beam that emerges from the objective is incident at an oblique angle at the coverslip-sample interface and totally internal reflected. In contrast to confocal FCS, the generated observation volume is completely confined to the surface and background fluorescence as well as scattered light from the bulk is efficiently suppressed. Our method, called objective-type TIR-FCS in the following, features an increased collection efficiency compared to existing techniques that combine evanescent wave excitation and FCS. Existing techniques use total internal reflection on the surface of a prism to generate an evanescent field. This leads to a configuration where the choice of objectives is limited to air or water-immersion objectives. In our system we use a high NA oil-immersion objective, specially conceived for TIR applications, which collects light efficiently. The collection efficiency is further enhanced by a naturally occurring change of the emission properties of fluorophores close to interfaces between dielectric media. The presence of the interface favors emission into the optically denser medium so that about 60% of the emitted light can be collected. These factors, together with a reduced observation volume lead to a very sensitive method with a high potential for applications in single molecule detection and analysis. The performance of the proposed method was experimentally shown for measurements on molecules subject to Brownian motion and binding to modified coverslips. In particular, it was experimentally shown that objective-type TIR-FCS features high signal-to-background ratio on a single molecule level. In this thesis, concise derivations of analytical expressions for autocorrelation functions for diffusion and most important, the case of ligands reversibly binding to a single and localized binding site are presented. The derived model allows for the quantitative determination of binding rates for a single receptor. We strongly believe that the application of these results in the context of investigations of receptor-ligand binding kinetics will allow for deeper understanding of cellular signaling. Moreover, this thesis discusses the applicability of the proposed method in enzymology. Enzymes, as most proteins are subject to continuous changes of their structure or conformation. These conformational changes are correlated with the function of the enzyme. In the discussed example the enzyme catalyzes an oxidation where the product is fluorescent but the substrate is not. The function of the enzyme i.e. the recurring product formation leads to observable intensity fluctuations. Since function and conformational states are correlated, conformational fluctuations can be investigated by means of FCS as was already shown for confocal FCS. A technique closely related to FCS is fluorescence lifetime spectroscopy (where lifetime refers to the mean lifetime of the electronic excited state). Whereas in FCS the relaxation after random deviations from thermal equilibrium is investigated, relaxation of excited fluorophores towards their electronic ground-state is investigated in lifetime spectroscopy. The technique is used for e.g. discrimination between fluorophores with different lifetimes. Lifetime spectroscopy combined with imaging is used in many domains of life-science, including microarray reading and medical diagnostics. In preliminary work we developed a novel approach to perform lifetime imaging that is based on a multiplexing technique. The proposed method requires no mechanical scanning stage and only a single-point detector. Furthermore, noise is reduced under certain circumstances if the signal is low. Characteristics of this technique as well as advantages and disadvantages are shortly discussed.

EPFL2006

Approches numériques du transport de charges dans les semiconducteurs organiques

Hocine Houili

Using plastics or dyes like molecular semiconductors to make optoelectronic devices at low cost is a project in industry that is of great interest to the "Information Community" of this beginning of the 21st century. Some applications of this technology have already been realized including flexible flat-panel displays made with organic light-emitting diodes, organic transistors for active matrices, organic solar cells and sensors. In all these applications it is essential to deduce and understand the laws that determine the charge transport and the light emission in these materials. The goal of this thesis is to contribute to the theoretical models that describe these transport processes. In order to predict the behaviour of charge carriers in a given device, one can choose two methods. One can either numerically solve the master equations that describe the general behaviour of charges and currents in each part of the device, or one can simulate the detailed behaviour of each charge in the device by fixing the conditions of its movement using a procedure known as "Monte Carlo". In this thesis I addressed the two approaches. I have been interested successively in the prediction of the electric properties of multilayer light-emitting devices, considered as a whole. Then I was able to understand in detail the processes accruing at the organic-organic interfaces by using the Monte Carlo method. My last project involved the study of the channel of an organic transistor. In each one of these cases I took account of the characteristic features of small molecule organic materials in order to develop models for charge transport for the study and optimization of two important types of organic devices : organic light-emitting diodes and field-effect transistors. Amorphous organic semiconductors are mainly used for the fabrication of organic diodes. They are characterized by an energetically disordered density of states that is assumed to be Gaussian. The transport of charges in these materials occurs via hopping from one molecule to another in this density of states. The correlations between the energies of the molecular sites have important effects on transport ; the dependence of mobility on the applied electric field in particular. If the energetic disorder is due to the random orientations of the permanent dipoles of the molecules, then the correlations between the orientations of these dipoles can profoundly change the spatial configuration of the energetic disorder and consequently the charge transport. Due to the fact that organic diodes often comprise of multiple organic layers, understanding device behaviour at the organic-organic interfaces is of critical importance. Electrons and holes accumulate close to these interfaces and they are therefore more likely to recombine and emit light. The Coulomb interactions between the charge carriers and the energy disorder are at the origin of complex processes taking place at these accumulation regions. I studied these processes through a 3D multi-particle Monte Carlo simulation. The short-range Coulomb repulsion forbids the double-occupancy of the sites and shifts the energy level for injection of carriers across the interface upward, thus increasing the electric current of the diode. The long-range Coulomb interactions increase the electric field and the current at the interface although this increase is less important than suggested by 1D models. Effects related to the hopping process such as the effect of the exact form of the hopping law and backward or return hop at the interface are clearly discussed. The Monte Carlo simulations are cross-compared with an analytical model for hopping transport across the interface. This comparison made it possible to understand other aspects of the physical processes at organic-organic interface and supports the Monte Carlo simulations. The study of the electron-hole recombination showed a decrease of the cross-section with an increase of the applied electric field, but this decrease is less than what can be expected by the classical Langevin theory. In spite of their efficiency, Monte Carlo simulations are not attractive when modelling complex multi-layer diodes. The 1D models are better suited in this case. A 1D model called MOLED, which was developed at Laboratoire d'Optoélectronique des Matériaux Moléculaires (LOMM) for the simulation of the organic diodes, is used and described in detail in this thesis. We used MOLED to explore the effect of the energy correlations on the electric field dependence of the mobility. In fact we simulated the time-of-flight experiment, a common method used to determine of the carrier mobility. The crystalline organic semiconductors achieve mobility performances close or even better than amorphous silicon. Their use for the fabrication of field-effect transistors is thus a good choice. The models for charge transport in crystalline organic materials differ much from their counterparts for amorphous organic materials. Indeed band models are more appropriate to describe charge transport in crystalline organic materials. However it is very important to take into account the effects of electronic polarization in these models. I developed a method of calculation of these effects of polarization in the bulk of the organic semiconductor and I extended it to the case of the interface with a dielectric insulator, a situation encountered in the channel of the organic transistor. These calculations showed that when the polarity of the dielectric increases the inter-molecular transfer integral decreases. This is confirmed by experimental measurements showing increasingly low values of mobility when the permittivity of the insulator increases.

EPFL2006

Stencil-nanopatterned back reflectors for thin-film amorphous silicon n-i-p solar cells

Christophe Ballif, Jürgen Brugger, Franz-Josef Haug, Mona Julia Katharina Klein, Céline Pahud, Andreea Veronica Savu, Oscar Vazquez Mena

We fabricated amorphous silicon n-i-p solar cells with two types of nanopatterned back reflectors using stencil lithography. One reflector type has a plasmonic grating that is embedded in the ZnO layer; the other one has a metallic grating patterned on top of the Ag layer. From comparing the short-circuit current densities of the two device types, we conclude that light trapping through grating coupling is more efficient than coupling of light through the excitation of localized surface plasmons. The back reflectors were patterned with dot arrays by evaporation of Ag through millimeter-size stencil membranes. The stencils themselves were patterned by wafer-scale nanosphere lithography. The dot arrays have a periodicity of 428 nm and efficiently scatter light in the near-infrared wavelength range. Both back reflectors types lead to the same morphology for the silicon films. This allows us a fair comparison of the two light coupling mechanisms. We found a 14% and 19% short-circuit current density enhancement for the plasmonic and for the metallic grating, respectively. The external quantum efficiency gains between 550 and 650 nm show similar guided modes resonances for both device types, but the excitation is stronger for the device with the metallic grating.

Ieee2012

Single molecule detection and fluorescence correlation spectroscopy on surfaces

Kai Hassler

EPFL2006

Approches numériques du transport de charges dans les semiconducteurs organiques

Hocine Houili

EPFL2006