π-Conjugated Donor-Acceptor Systems as Metal-Free Sensitizers for Dye-Sensitized Solar Cell Applications

High extinction coefficients and easily tunable spectral properties of π - conjugated donor-acceptor dyes are of superior advantage for the design of new metal- free organic sensitizers for applications in dye-sensitized solar cells. Ultrafast transient absorption spectroscopy on the femtosecond and nanosecond time scales provided deep insights into the dependence of charge carrier dynamics in fully organic dye/TiO2 systems on i) the donor-acceptor distance, ii) the π-conjugation length, and iii) the coupling to TiO2 by different anchoring groups. Importantly, the observed differences in charge transfer dynamics justify the variations of photovoltaic performances of the dyes as applied in solar cell devices. This leads to the conclusion that the photoconversion efficiencies strongly depend on a delicate interplay between the dyes’ building blocks, i.e. the donor, the π-conjugated spacer and the anchor/acceptor moieties, and may easily be tuned by molecular design.

Novel organic dyes for enhanced red to near IR response in dye sensitised solar cells

The aim of this work was to develop new, organic dyes, capable of harvesting photons in the red to near-IR region of the spectrum. A series of squaraine and tricarbocyanine dyes were produced and characterised and their optical and redox properties studied. The results of initial photovoltaic tests, followed by optimisations of cell performance, have also been presented. These clearly demonstrate the effectiveness of these dyes in solar cells. A total of 12 new squaraine dyes were successfully synthesised, seven of which were tested in "dye-sensitised" solar cells. The efficiencies ranged from 1.2%-3.7%, for the best dye [B1]. It was concluded that enhanced performance could be achieved in the presence of chenodeoxycholic acid (CDCA) and tetrabutylpyridine (TBP). These additives both help to prevent aggregation and increase the cell potential, limiting charge collection losses and enhancing performance. Three new tricarbocyanine dyes were also synthesised, two of which were used in solar cells. Unfortunately, due to the interaction of [B12] with the electrolyte, the dye proved to be unstable, as both the absorption maxima in UV-vis and fluorescence emission wavelengths were shifted to higher energies. Thus, the red response of the dye was significantly reduced and photovoltaic performance hindered. A limited photo-response of [B14] was also seen, although this dye appeared to be very stable in the presence of the electrolyte. To deduce the possible reasons for the poor performance of these dyes, their optical and electrochemical properties were investigated. Thus, cyclic voltametry was employed to identify the redox potentials of the dyes and their charge injection and recombination dynamics were studied through nanosecond time-resolved transient laser spectroscopy. It was concluded that the dyes theoretically possess the ideal characteristics for solar cell function and that the problem of [B14] lay in the purity of the dye. [B14] proved to be very difficult to purify as the dye was unstable in solution and decomposed on the columns employed in chromatography. Fortunately the dye appeared to be stable in the presence of an electrolyte when adsorbed on TiO2. The dye gave an IPCE of 12% between 800 – 900nm, which is particularly impressive, especially if the purity of the dye is considered. A new method of purification must be found however, if photovoltaic performance is to be enhanced. Finally, the effects of a compact blocking layer on device performance were studied. It was clearly demonstrated that a compact layer was essential. This was investigated and a relationship between the structure of the dye and the necessity of the blocking layer was established.

EPFL2006

Molecular design of metal-free D–π-A substituted sensitizers for dye-sensitized solar cells

Leila Alibabaei, Davide Di Censo, Robin Humphry-Baker, Jacques-Edouard Moser, Nuttapol Pootrakulchote, Joël Teuscher, Mingkui Wang, Yuxiang Yu, Shaik Mohammed Zakeeruddin

Novel donor-p-acceptor (D--A) dyes, coded as SD-1, SD-2 and SD-5, were designed and synthesized for dye-sensitized solar cells. All these dyes comprised the same donor and acceptor units while the oligo thiophene units were introduced as linkers between the donor and acceptor units. The photophysical and electrochemical properties of the dyes were investigated by UV/vis spectrometry and cyclic voltammetry. The dyes were subsequently tested as sensitizers in dye-sensitized solar cells. Photovoltaic performance of the device with SD-2 dye showed maximum monochromatic incident photon-to-current efficiency (IPCE) of 82% and an over all conversion efficiency of 6.2% under full sunlight (AM 1.5G, 100 mW cm^2) irradiation.

2010

Solid-State Sensitized Heterojunction Solar Cells

Soo-Jin Moon

Dye-sensitized solar cells (DSCs) are considered as an emerging technology in order to replace conventional silicon solar cells or thin film solar cells such as amorphous silicon, CIGS, and CdTe. Liquid electrolytes containing iodide/triiodide redox couple have a durability problem due to the corrosion of metal contacts. In order to improve the long-term stability of DSC device it is important to find an alternate efficient redox couple. In search of this we are using 2,2',7,7'-tetrakis-(N,N-di-methoxyphenylamine)- 9,9'-spirobifluorene (spiro-OMeTAD) as a hole transport material for solid-state dye-sensitized solar cells (SSDSCs). In comparison to the liquid electrolytes the efficiencies of SSDSCs are inferior, they are around only 30% of the efficiencies obtained with the liquid electrolytes. In optimizing the device performance and stability of SSDSCs, various light harvesting systems are employed to enhance a photovoltaic performance and investigated their properties in SSDSCs. In SSDSCs we use thin TiO2 films to avoid the pore-filling problem of HTM. Hence it is critical to use high molar extinction coefficient dyes with an efficient light harvesting capability for SSDSCs. Representative ruthenium sensitizers such as N719 or Z907 have shown good and stable performances in liquid electrolyte-based DSCs. However, their performances are low in SSDSCs due to insufficient light harvesting in thin mesoporous TiO2 films. A new family of heteroleptic polypyridyl ruthenium sensitizers having thiophene units was employed to increase the light harvesting capabilities and their applicability in SSDSCs. These new dyes could improve the absorbed photon-to-current conversion efficiencies as well as power conversion efficiencies due to their high molar extinction coefficients. The thiophene units of the ancillary ligands not only enhanced molar extinction coefficients but also augmented electron lifetime in the devices. In general, ruthenium sensitizers possess lower molar extinction coefficients compared to organic dyes. In order to increase the molar extinction coefficients and bathochromic shift in the absorption spectra of organic dyes, we applied donor-acceptor concept in organic dyes with different π-conjugation bridges. Consequently, we achieved 6 % power conversion efficiency at AM 1.5G solar irradiation (100 mW/cm2) in a solid-state dye-sensitized solar cell. Transient photovoltage and photocurrent decay measurements showed that the enhanced performance of this device was ascribe to higher charge collection efficiency over a wider potential range. We also examined near infrared absorbing dyes and they could be employed to different device architectures such as tandem cells, Förster Resonance Energy Transfer, or co-sensitization to substantiate panchromatic response. Another interesting type of sensitizers is semiconductor or quantum dots due to their unique properties. However, the efficiency of the semiconductor-sensitized solar cells was only 1-2 % range. Recently, much improved efficiencies were reported with Sb2S3-sensitized cells using different hole conductors. The Sb2S3-sensitized cells with spiro-OMeTAD demonstrated a very high incident photon-to-conversion efficiency (IPCE) of 90 %. This excellent result shows that the semiconductor sensitizers are promising candidate as light absorbers for SSDSCs. Most of the standard ruthenium and organic dyes have the limited absorption in near infrared region of the solar spectrum. Porphyrin sensitizers possess strong absorptions in the visible and near infrared region and they have good chemical, photochemical and thermal stability. However, the power conversion efficiency of SSDSCs devices using a novel D-π-A porphyrin we reached only 1.6 %. In order to improve a cell performance, porphyrin was co-sensitized with an organic dye to increase light harvesting capability in the green wavelength region as well as to reduce the dye aggregation. Instead of spiro-OMeTAD a polymer hole conductor was applied, which had intense spectral response in the visible region. Interestingly, in this system the polymer hole conductor showed dual functions, as a light absorber and a hole transporter. This hybrid solar cell exhibited a clear panchromatic response and improved the power conversion efficiency of device compared to the cell with spiro-OMeTAD.

EPFL2011

Novel organic dyes for enhanced red to near IR response in dye sensitised solar cells

EPFL2006

Solid-State Sensitized Heterojunction Solar Cells

Soo-Jin Moon

EPFL2011