Modelling of 2G HTS Coated Conductors for Fault Current Limiter Applications

Daniele Colangelo
EPFL, 2013
Thèse EPFL

Résumé

Thanks to recent scientific achievements, second generation high-temperature superconductor coated conductors (HTS-CCs) can carry enormous current densities with reduced losses. In addition, they are able to switch from a negligible resistivity state to a high resistivity state (quench) in a very fast time. The most promising application for this technology is represented by resistive superconducting fault current limiters (SFCLs). These devices enable us to operate the grid at larger power flows without the need of expensive upgrading interventions. One of the crucial challenge for the design of SFCLs is to deal with the inhomogeneous properties the superconducting materials present. The inhomogeneity of the material properties causes a non uniform transition to the high resistivity state. The consequence is a local heat generation. As HTS-CCs are characterized by low thermal conductivity, the heat does not diffuse longitudinally and the conductors are exposed to local thermal runaway. This Ph.D. thesis focuses on the numerical modelling of (RE)BaCuO-based HTS-CCs for resistive fault current limiter applications. The purpose of numerical modelling is to improve the HTS-CCs thermal stability and to optimize the design of resistive SFCLs. First, we develop a thermal-electrical coupled model that describes the transient response of long length (hundreds of meters) inhomogeneous HTS-CC candidates. The implementation of the inhomogeneous properties is based on Gaussian distributions derived from commercial wires. The electrical part of the model has been tuned to fit experimental measurements made on commercial coated conductors. The thermal part of the model has been validated with the support of finite element methods (FEMs). Then, we extended the modelling of HTS-CCs to SFCL modules. The model of a resistive SFCL has been interfaced with the characteristic parameters of two real medium voltage grids. The effect of the tape inhomogeneity has been analyzed under real fault scenarios. Afterwards, we used FEM calculations to investigate the possibility of improving the thermal stability of commercial HTS-CCs. In this respect, we analyzed the effects of a medium inserted between a HTS-CC and the cooling bath. The benefits of the concept idea has been demonstrated through a simplified 2D electro-thermal model (2D ET). In its turn, the assumptions used to develop the 2D ET model have been validated with a 2D magneto-thermal model (2D MT) and a 3D electro-thermal model (3D ET). The 2D MT model has been used to compare the magnetic and the thermal dynamics of a HTS-CC, whereas the 3D ET model has been used to study the quench propagation across the width and along the length of a HTS-CC.

Official source

https://infoscience.epfl.ch/record/189858?ln=fr

À propos de ce résultat

Cette page est générée automatiquement et peut contenir des informations qui ne sont pas correctes, complètes, à jour ou pertinentes par rapport à votre recherche. Il en va de même pour toutes les autres pages de ce site. Veillez à vérifier les informations auprès des sources officielles de l'EPFL.

Concepts associés

Chargement

Publications associées

Chargement

Daniele Colangelo
EPFL, 2013
Thèse EPFL

Résumé

Official source

https://infoscience.epfl.ch/record/189858?ln=fr

À propos de ce résultat

Concepts associés (29)

Concepts associés

Chargement

Publications associées (67)

Publications associées

Chargement

Inhomogeneity effects in HTS coated conductors used as resistive FCLs in medium voltage grids

Daniele Colangelo, Bertrand Dutoit

For resistive fault current limiters (RFCLs) based on high temperature superconducting coated conductors (HTS-CCs), inhomogeneity, in terms of critical current and geometrical imperfections such as stabilizer and substrate thicknesses, plays a very important role and it may limit the penetration of such devices into the electrical market. This paper presents an electrothermal model, developed in SimPowerSystem™, able to describe the transient response of HTS-CC candidates with different degrees of inhomogeneity, both in terms of critical current and of stabilizer thickness. Critical current inhomogeneity has been modeled with Gaussian distributions. The layer thicknesses used in the simulations have been chosen by fitting the temperature dependence of real tape resistances. Our approach considers relative inhomogeneity positions as well as thermal conduction along the HTS-CC length. The model is tuned using experimental measurements made on ReBaCuO coated conductors. A new dynamical thermal calibration of the model is proposed using finite element method calculations. Inhomegeneity effects with different possible faults (e.g. three phase and single phase short-circuit) are presented.

Institute of Physics2012

Chargement

Modeling and Characterization of Coated Conductors Applied to the Design of Superconducting Fault Current Limiters

François Roy

The Superconducting Fault Current Limiter (SFCL) appears to be a device of great interest to efficiently build the electrical grid of tomorrow. With the recent progress made by the superconducting wires manufacturers, there are needs coming from the industry to evaluate the potential of such devices. In the present thesis work, the behavior under external field and transport current of the last generation of wire is investigated. This study is conduct both experimentally and numerically in order to link the physics occurring at the wires level to the design of SFCLs as a whole. From the nature of the material, the resistance appears non-uniformly in high temperature superconductors. For the purpose of building SFCLs it is important to obtain a fast and uniform resistive transition (quench) when a fault occurs through those conductors. This in order to reduce the local heat generation that may damage the device. This fast quenching property is related to the Normal Zone Propagation Velocity (NZPV). In this work the NZPV is measured using a localized magnetic field to initiate quenches in commercial coated conductors. Those velocities have been measured to be larger than 14 cm/s for pulsed currents above the critical value. The NZPV experiments have demonstrated that the superconductor non-uniformity (generated by the localized field) helps to reduce the initial delay before the quench initiation for transport currents in the range of the critical value. However, for larger transport currents the effect of the non-uniformity on the delay is less important since, with increasing transport current amplitudes, the normal state transition has shown to occur more as a consequence of the heat generated in the stabilizer than as the unique consequence of the advancement of the normal zone in the superconductor. From the experimental measurements, it has been shown that a reduction of the liquid-nitrogen temperature (subcoooled) increases the NZPV. This effect has been observed taking into account of the increase of the critical current associated with the temperature reduction. Nevertheless, it is not clear if it is the heat transfer or the estimation of the critical current that is responsible for this effect. In order to validate the numerical models, time-resolved voltage traces obtained from the experiments have been compared to the outputs of the models. Those are based on the thermal- and electrical-diffusion equations. From the simulations, it has been demonstrated that the NZPV can be increased by three methods: by using a thick diffusive substrate, by inserting a resistive interface between the superconductor and the stabilizer as well as by increasing the heat generation in the stabilizer. In light of those results, it seems that the insertion of a resistive layer is the most promising approach to improve the NZPV in coated conductors. As a matter of fact, a resistive interface increases the normal-zone size and keeps an acceptable temperature level along the conductor during quenches. The present work allowed to simulate the flux-flow regime in coated conductors. Comparing those simulations to experimental data have shown that the power-law may be inappropriate to simulate this regime under weak external magnetic fields. In addition, it appears that the role of transient heat transfer with the surroundings needs to be studied in more details to determine the specifications of a prospected SFCL made of coated conductors.

EPFL2010

Chargement

High-Temperature Superconductors (HTS) can be superconducting in liquid nitrogen 77 K, holding immense promises for our future. They can enable disruptive technologies such as nuclear fusion, lossless power transmission, cancer treatment devices, and technologies for future transportation. In the past years, the numerical models to describe the electrical resistivity of REBCO commercial tapes for devices working near and above the critical current, have been shown to be not accurate or very empirical. The resistivity in this regime, in fact, is not very well known. The lack of this knowledge is a significant issue in developing quality simulation tools. The major challenge in retrieving such properties lies in the fact that when I>Ic, heating effects, and thermal instabilities can quickly destroy the conductor if nothing is done to protect it. Moreover, due to the current sharing between the layers, it is difficult to know the amount of current carried by the superconducting layer and its resistivity. The present work aims to understand better the overcritical current regime combining ultra-fast pulsed current measurements performed on HTS REBCO based coated conductors with Finite Element Modeling. The experimental activities were carried out mostly at EPFL and in part at PM and KIT. The modeling activities were carried out between EPFL and KIT. The major result is a resistivity relationship describing the overcritical current regime to be used in numerical simulations of REBCO tapes. The first part of the thesis illustrates a post-processing method based on the so-called Uniform Current (UC) model to estimate the REBCO material's resistivity in the overcritical from experimental measurements. Pulsed current measurements as short as 15 us and with current magnitude up to 5 Ic were performed in liquid nitrogen bath 77 K on samples from various manufacturers, without damaging the tapes. The second part of the thesis discusses a post-processing method based on regularization of data to treat the experimental measurements extracted in the overcritical current regime. The output of this technique is a look-up table that can be shared with interested partners and used in numerical modeling afterward. The third part of the thesis presents the overcritical current model (rho-\eta\beta): a mathematical relationship of the overcritical current regime based on measurements performed between 77 K and 90 K and in self-field conditions. We compare such models with the power-law model, and we provide a short discussion of the fitting parameters and their typical values. The last part of the thesis discusses the overcritical current model, based on experimental measurements obtained as outlined above. The model was validated experimentally and used to show that for the case of a superconducting fault current limiter when the power-law model is used to model its electro-thermal response, the device quenches faster than with the overcritical model. In conclusion, this work can help optimize the use of superconductors and, consequently, the stabilizer. More interestingly, it opens the study of the overcritical current regime, a new exciting aspect of REBCO commercial tapes. This project has received funding from the Swiss Federal Office of Energy SFOE under grant agreement SI/500193-02.

EPFL2021

Chargement

Modeling and Characterization of Coated Conductors Applied to the Design of Superconducting Fault Current Limiters

François Roy

EPFL2010

EPFL2021