Between photocatalysis and photosynthesis: Synchrotron spectroscopy methods on molecules and materials for solar hydrogen generation

Energy research is to a large extent materials research, encompassing the physics and chemistry of materials, including their synthesis, processing toward components and design toward architectures, allowing for their functionality as energy devices, extending toward their operation parameters and environment, including also their degradation, limited life, ultimate failure and potential recycling. In all these stages, X-ray and electron spectroscopy are helpful methods for analysis, characterization and diagnostics for the engineer and for the researcher working in basic science.This paper gives a short overview of experiments with X-ray and electron spectroscopy for solar energy and water splitting materials and addresses also the issue of solar fuel, a relatively new topic in energy research. The featured systems are iron oxide and tungsten oxide as photoanodes, and hydrogenases as molecular systems. We present surface and subsurface studies with ambient pressure XPS and hard X-ray XPS, resonant photoemission, light induced effects in resonant photoemission experiments and a photo-electrochemical in situ/operando NEXAFS experiment in a liquid cell, and nuclear resonant vibrational spectroscopy (NRVS). (C) 2012 Elsevier B.V. All rights reserved.

Coupling of electrocatalysts to photoabsorbers for solar fuels production

Carlos Gilberto Morales Guio

The direct transformation of sunlight into fuels and chemicals has attracted considerable attention for the potential impact on the storage of solar energies at large scales and the reduction of CO2 emissions. More than 80% of our current global energy consumption comes from the burning of non-renewable fossil fuels which produces enormous quantities of CO2 and contributes to global warming. We believe today that the key to reduce our dependence on exhaustible natural resources and limit the emission of greenhouse gases is the transition to CO2-free renewable energy sources. However, harvesting of energy from renewable sources (i.e. solar, wind, tidal) is intermittent and the deployment of devices for their transformation into useful forms of energy (i.e. electricity, chemicals, fuels, biomass) in a global scale is conditioned upon the improvement in efficiency of the energy storage mechanisms. A promising approach to store energy is the use of sunlight to drive the production of hydrogen fuel from water. Hydrogen produced from water and sunlight can be transformed back to electricity on demand or be used to generate mechanical energy in cars to power the transportation industry. The oxidation of hydrogen generates useable energy and at the same time exhaust clean, carbon-free water as the only product. Therefore, the production of hydrogen using a renewable energy source in an efficient and inexpensive device has the potential to discourage the continued use of fossil fuels and improve our environment. The viability of any mechanism for the storage of sunlight as fuel will depend on the reduction of energy penalties during the transformation process. Electrocatalysts are advanced materials that bring into one active site electrons and molecules in the appropriate orientation to lower activation energy barriers, accelerate rate of transformations and improve overall efficiencies for chemical reactions. The best catalysts for water splitting are precious metals such as Pt, Ir and Ru, which show superior rates of reaction at low overpotentials. However, these noble metals are too expensive and scarce for large scale applications. This thesis summarizes our recent research in the preparation, characterization, and application of Earth-abundant electrocatalysts for solar water splitting. Although in the last decade a great number of efficient and inexpensive electrocatalysts have been reported, methods for the deposition of these materials on the surface of photoabsorbers are rarely reported. This work shows various simple and scalable techniques for the deposition of hydrogen and oxygen evolving electrocatalysts on the surface of photocathodes and photoanodes, respectively. Surface-protected photocahodes were activated for solar hydrogen production in alkaline conditions with MoS2+x, Ni-Mo and Mo2C. A novel method for the deposition of an optically transparent amorphous iron nickel oxide oxygen evolution electrocatalyst is also reported. The catalyst was deposited on both thin film and high-aspect ratio nanostructured hematite photoanodes. The low catalyst loading combined with its high activity at low overpotential results in significant improvement on the onset potential for photoelectrochemical water oxidation. This transparent catalyst further enables the preparation of a stable hematite/perovskite solar cell tandem device, which performs unassisted water splitting.

EPFL2016

Solar Energy Stored as Hydrogen

Jérémie Minh-Châu Brillet

The tandem photoelectochemical (PEC) cell based on oxide semiconductors for water splitting offers a potentially inexpensive route for solar hydrogen generation. At the heart of the device, a nanostructured photoanode for water oxidation is connected in series with one or two dye-sensitized solar cells (DSCs) that provide an extra bias to photogenerated electrons in order to perform water reduction at the platinum cathode. In Part A of this thesis, after reviewing the different technologies available for solar hydrogen production, I focus on different possible architectures for photoanode / DSC tandem cells enabled by the most recent advances in the field. First, the development of all organic squaraine dyes having a narrow absorption bandwidth extending into the near infrared region and a broad transparent window in the visible region of the spectrum have allowed the design of a new photoanode / DSC / DSC tandem architecture. The "Back DSC" tandem cell, where two DSCs placed side-byside exploit the photons transmitted by a single photoanode is the conventional architecture. In this thesis, I demonstrate the inverted "Front DSC" architecture, which allows the use of non-transparent lower cost metallic substrate for the photoanode, as well as the "tri-level" tandem cell where a panchromatic "black" dyebased DSC exploits the energy transmitted by the photoanode and the squaraine dyebased DSC. Opto-electronic studies on each of these three architecture are performed and the respective solar-to-hydrogen conversion (STH) efficiencies of 1.16 %STH, 0.76 %STH and 1.36 %STH are assessed. Finally, I leverage recent findings in the field of high voltage DSCs to demonstrate for the first time a tandem cell using only one photovoltaic cell to perform complete water splitting at efficiencies as high as 3.10 % STH. Such a result represents a ten-fold improvement over previous demonstrations with this class of device. This work describes a breakthrough in the inexpensive solar-to-chemical conversion using improved photon management in a dual-absorber tandem cell and undoubtedly constitutes a benchmark for solar fuel production by solution processable oxide-based devices. In Part B, I focus on the photoanode for the oxygen evolution reaction. Hematite (α-Fe2O3) is a great candidate material for this application due to its availability, low cost, non-toxicity and appropriate band gap allowing extensive absorption in the visible part of the spectrum. However, it suffers severe drawbacks, among which are poor majority carrier conductivity and a short diffusion length of minority charge carrier with regard to photon penetration depth. This circumstance causes most photogenerated charges to have a low probability of reaching the semiconductor / liquid junction and thus to participate in the water oxidation reaction. This feature implies the use of hematite morphologies having feature size in the range of 10-20 nm. A solution-based colloidal approach offers a simple and easily scalable method to obtain nanostructured hematite. However, this type of nanostructure needs to be exposed to an annealing step at 800 °C to become photoactive. This has been attributed to the diffusion of dopants from the substrate. In addition, this annealing step sinters the 10 nm particles colloid into a feature size approaching 100 nm. Here, I first show the effect of intentionally doping this material on the sintering and photoactivity. I then demonstrate a method that allows for the first time to apply high temperature annealing steps while controlling the feature size of the nanoparticles. Such an approach can be applied to any kind of nanostructure. This latter strategy coupled to further passivation of surface states allowed an improvement of the net photoactivity of this type of photoanode by a factor of two. A reproducible net photocurrent exceeding 4 mA.cm-2 was obtained. This result represents the highest performance reported for hematite under one sun illumination. In Part C of this thesis, I present several synthesis methods for titania nanostructures acting as photoanodes in the DSC. In this photovoltaic cell, the electronic loss that is typically discussed is the slow transport induced recombination. Charges recombining before reaching the electrode have a detrimental influence on the photocurrent and photovoltage. Several approaches have been proposed in order to reduce interfacial recombination and improve charge collection in liquid electrolyte and solid state-DSCs (ss-DSCs) including the use of radial collection nanostructures, one-dimensional ZnO and TiO2 nanorods, and nanowires as photoanodes. Even though these approaches show great promise, they have yet to achieve power conversion efficiencies above 5% in liquid electrolyte DSCs and 1.7% in ss-DSCs. In this part of my thesis, I expose results on the strategies I have pursued during the course of my PhD to improve the dynamics in the liquid and ss-DSC. From one dimensional titania nanotube arrays, I have moved to tri-dimensional fibrous network of crystalline TiO2 and more complex host-passivation-guest photoelectrodes.

EPFL2012

Nanostructured Electrocatalysts for Water Splitting Reactions

Lucas-Alexandre Stern

At the dawn of the 21st century, mankind is facing an important energy challenge. Future energy demand can only be met by large scale exploitation of renewable energy resources. Solar energy is abundant, with a sufficient capacity for the growing energy demand. However, it is necessary to implement renewable energy storage means. Hydrogen is considered as the energy carrier of the future. An energy economy based on hydrogen is viable only if hydrogen is produced from sustainable means. Water electrolysis is the most promising technique to produce hydrogen directly from water. Yet, the efficiency is limited and electrocatalysts are required to drive both the hydrogen evolution reaction and oxygen evolution reaction. Scarce and expensive materials are currently used to drive these reactions. It is, thus, imperative that efficient Earth-abundant catalysts are developed. Nanostructuring enhances the performance of inexpensive materials for water splitting and several catalysts were studied for this goal. Chapter 2 describes the application of nanostructuring technique to the archetypical catalysts that are nickel oxides for oxygen evolution. The prepared nanoparticles show superior activity towards oxygen evolution than that of their bulk counterpart. The ultrafine size of nanoparticles synthesized allowed the exposure of a higher number of active sites. The activity for oxygen evolution was, thus, significantly enhanced. We also detailed that short conditioning of the electrode improved the performance of the evaluated materials. In chapter 3 we carefully studied nanoparticles and nanowires of nickel phosphide. The catalysts is known to be really active for hydrogen evolution. Our group suspected that this material was, also, a potential oxygen evolution catalyst. We proved, for the first time, that nickel phosphide is a remarkable oxygen evolution catalyst. Under alkaline conditions, used for oxygen evolution, we observed an in-situ formation of a core-shell heterostructure, a typical nanostructure architecture. The surface oxidation of this material allowed high oxygen evolution capabilities. We concluded that careful oxidation of nanostructured materials, as observed for nickel phosphide, is essential for the preparation of future outstanding oxygen evolution catalysts. Chapter 4 details the fabrication of direct solar-to-fuel electrode using cobalt phosphide as hydrogen evolving catalyst. Instead of using the electrical energy provided by solar energy, solar irradiation on the developed assembly allows direct hydrogen production. The careful design of the light-sensitive electrode (photocathode) is detailed. Simple incorporation of cobalt phosphide by means of photodeposition alleviates the cost of the electrode fabrication. The assembled electrode is active for hydrogen evolution under visible light irradiation. In the chapter 5 we sought to fabricate a 3-dimensional hydrogen evolving catalyst. This nanostructure is based on polymer brushes on a flat conducting substrate. Once the brushes are grown on the substrate, a molybdenum sulfide catalyst is then incorporated by simple soaking technique. We were able to tune the loading of the catalyst and the corresponding activity by changing the polymer properties. The height of the polymer was modified as well as its packing density. The resulting activity proved superior to similar approaches and to previous reports on carefully engineered molybdenum sulfide catalysts.

EPFL2017