A Wide Tuning Range 4th-Order Gm-C Elliptic Filter for Wideband Multi-Standards GNSS Receivers

A 4 th order Gm-C elliptic low-pass filter with a wide continuous tuning range is presented. The continuous tuning is achieved by means of a new tuning circuit which adjusts the bias current of the Gm cell's input stage to control the cut-off frequency. With this tuning circuit, power efficiency is achieved by scaling down the power consumption proportionally to the cut-off frequency while keeping the linearity near constant over a wide range of frequencies. To extend the tuning range of the filter, Gm switching was employed which also acts on the Gm cell's input stage without adding any switches in the signal path. The filter was fabricated using UMC 180-nm CMOS technology on an active area of 0.23 mm2. Its cut-off frequency ranges continuously from 7.4 to 27.4 MHz. This wide range of possible tuning makes the filter suitable for modern wideband GNSS signals in zero-IF receivers. The filter consumes 2.1 and 7.5 mA (from 1.8 V) at its lowest and highest cut-off frequencies, respectively, and achieves a high input IP3 of up to −1.3 dBVRMS.

CMOS ASIC Design of Multi-frequency Multi-constellation GNSS Front-ends

Saeed Ghamari

With the emergence of the new global navigation satellite systems (GNSSs) such as Galileo, COMPASS and GLONASS, the US Global Positioning System (GPS) has new competitors. This multiplicity of constellations will offer new services and a much better satellite coverage. Public regulated service (PRS) is one of these new services that Galileo, the first global positioning service under civilian control, will offers. The PRS is a proprietary encrypted navigation designed to be more reliable and robust against jamming and provides premium quality in terms of position and timing and continuity of service, but it requires the use of FEs with extended capabilities. The project that this thesis starts from, aims to develop a dual frequency (E1 and E6) PRS receiver with a focus on a solution for professional applications that combines affordability and robustness. To limit the production cost, the choice of a monolithic design in a multi-purpose 0.18 µm complementary metal-oxide-semiconductor (CMOS) technology have been selected, and to reduce the susceptibility to interference, the targeted receiver is composed of two independent FEs. The first ASIC described here is such FEs bundle. Each FE is composed of a radio frequency (RF) chain that includes a low-noise amplifier (LNA), a quadrature mixer, a frequency synthesizer (FS), two intermediate frequency (IF) filters, two variable-gain amplifiers (VGAs) and two 6-bit flash analog-to-digital converters (ADCs). Each have an IF bandwidth of 50 MHz to accommodate the wide-band PRS signals. The FE achieves a 30 dB of dynamic gain control at each channel. The complete receivers occupies a die area of 11.5 mm2 while consuming 115 mW from a supply of a 1.8 V. The second ASIC that targets civilian applications, is a reconfigurable single-channel FE that permits to exploit the interoperability among GNSSs. The FE can operate in two modes: a ¿narrow-band mode¿, dedicated to Beidou-B1 with an IF bandwidth of 8 MHz, and a ¿wide-band mode¿ with an IF bandwidth of 23 MHz, which can accommodate simultaneous reception of Beidou-B1/GPS-L1/Galileo-E1. These two modes consumes respectively 22.85 mA and 28.45 mA from a 1.8 V supply. Developed with the best linearity in mind, the FE shows very good linearity with an input-referred 1 dB compression point (IP1dB) of better than -27.6 dBm. The FE gain is stepwise flexible from 39 dB and to a maximum of 58 dB. The complete FE occupies a die area of only 2.6 mm2 in a 0.18 µm CMOS. To also accommodate the wide-band PRS signals in the IF section of the FE, a highly selective wide-tuning-range 4th-order Gm-C elliptic low-pass filter is used. It features an innovative continuous tuning circuit that adjusts the bias current of the Gm cell¿s input stage to control the cutoff frequency. With this circuit, the power consumption is proportional to the cutoff frequency thus the power efficiency is achieved while keeping the linearity near constant. Thanks to a Gm switching technique, which permit to keep the signal path switchless, the filter shows an extended tuning of the cutoff frequency that covers continuously a range from 7.4 MHz to 27.4 MHz. Moreover the abrupt roll-off of up to 66 dB/octave, can mitigate out-of-band interference. The filter consumes 2.1 mA and 7.5 mA at its lowest and highest cutoff frequencies respectively, and its active area occupies, 0.23 mm2. It achieves a high input-referred third-order intercept point (IIP3) of up to -1.3 dBVRMS.

EPFL2016

Adaptive frequency tracking and application to biomedical signals

Yann Prudat

The main information of a signal resides in its frequency, its amplitude (or its power) and in their temporal evolution. Thus, a great number of methods for instantaneous frequency estimation have been proposed in the literature. Most of these algorithms use an adaptive filter-based (notch or bandpass filter) structure. In many applications, the information of interest is present in more than one signal. However, to our knowledge no algorithm able to track the frequency on several signals has been presented in the literature. Usually, frequency components are estimated and extracted on each signal independently. Artifacts or noise relative to a specific signal can thus disturb the frequency estimation process. Moreover, low amplitude components present in every signal (but non dominant) will not be estimated. The objective in the first part of this thesis is to develop different methods able to extend existing frequency tracking algorithm in order to improve the quality of the estimate, in terms of estimation variance and robustness with respect to noise. The proposed methods can be applied to algorithms using adaptive filters for the frequency estimation. For the multi-signal frequency tracking extension, these methods use the redundancy of information present in the signals under study. A first approach uses a unique filter for every signal. A set of weights is computed, depending on a measure of the estimate quality, and makes it possible to balance the influence of each signal on the tracking filter update. The second approach consists in using a different adaptive filter for each signal. A set of constraints links the central frequencies of each filter so that they are as similar as possible. Both methods yield frequency estimates more robust with respect to noise and more stable, without any decrease in estimation accuracy. For the harmonic frequency tracking, we propose a method using the information present in the harmonic component to improve the estimate of the fundamental frequency. The proposed methods also permit to extract the signal components corresponding to the estimated frequencies. These components are very useful for subsequent study. In the second part of this thesis, the algorithms developed in the first part are applied to biomedical signals. Two different applications are studied in this work : electrocardiograms and electroencephalograms. Firstly, a frequency tracking algorithm as well as its multi-signal extension are used to predict the success of electrical cardioversion attempts in patients suffering from atrial fibrillation. The instantaneous frequency is estimated using the algorithms and the corresponding signal component is extracted from electrocardiograms recorded prior to the attempt. With a few parameters computed on the estimated frequency and the corresponding signal component, we were able to predict the result of the cardioversion attempt on our database comprising 18 patients with a success rate of 94% for both algorithms. We think that this result can be very useful for helping the clinician to choose the appropriate therapy for atrial fibrillation management. The developed algorithms are also used to track the oscillatory components present in electroencephalograms. The performance of the basic algorithm is illustrated using single-trial electroencephalogram signals from a visual evoked potential experiment. The algorithm is used to track the gamma component (30-50 Hz). It is able to successfully track the spectral component in spite of the fact that large amplitude variations are present in the signal. A complex version of the multi-signal extension is also used to have an algorithm able to track multiple frequency components on multiple signals. The performance of this algorithm is also illustrated with single-trial electroencephalogram signals. It was shown to be able to correctly track up to four frequency components simultaneously. The quality of the estimation is improved using multiple lead signals.

EPFL2009

Binaural reverberation using a modified Jot reverberator with frequency- dependent interaural coherence matching

Christof Faller, Fritz Menzer

An extension of the Jot reverberator is presented, producing binaural late reverberation where the interaural coherence can be controlled as a function of frequency such that it matches the frequency-dependent interaural coherence of a reference binaural room impulse response (BRIR). The control of the interaural coherence is implemented using linear filters outside the reverberator’s recursive loop. In the absence of a reference BRIR, these filters can be calculated from an HRTF set.