Publication

Integrated maintenance model for heavy haul tracks

Résumé

Due to the accumulation of traffic, the railway components are affected by the induced stresses. As a result, the geometry of the railways is degraded over time. The degradation occurs either through the partial loss of the track's geometry or through the development of a specific damage on the track component. The degradation of the vertical geometry is due to the permanent deformation of the granular materials that results from the progressive rearrangement of the granular particles from the ballast and subgrade layers. In order to reduce the impact of degradation, different methods of maintenance are used. Tamping is a common procedure to restore the track position of ballasted tracks. For the rails, a grinding process is used to eliminate partially rail roughness, while ballast renewal is employed when ballast material attains a certain level of deterioration. The different maintenance types are performed under different strategies. In the active approach, maintenances are executed according to pre-determined values of accumulated transported materials, while in the reactive strategy, a value of a structural or geometric parameter is used to determine the moment a maintenance must be executed. Therefore, the problem related to the degradation of railway tracks subjected to high loads, typically larger than 22.5tons/axle, is a particular case. These loads attain values of approximately 40 tons/axle, as in the case of railways for transportation of commodities. In a heavy haul scenario, the higher values of loads lead to extra amount of efforts on the track elements that may cause excessive damage in a component level, hence causing faster general track deterioration. The aim of this research is to provide answers related to the structural and geometric conditions under load increase and its consequence on maintenance, including a cost analysis. These results are useful for rail managers, so as to have a preview of certain potential structural and geometric consequences at the railway components. Moreover, the knowledge about the impact of maintenances on tracks' structure is useful for maintenance strategy selection. The maintenance costs, in a certain time period under different loads, assists to decide the strategy to follow in the case of load increasing planning. In this research, an accumulative track degradation model is developed and used to determine the struc-tural and geometric responses, and consequently the needs for maintenances over time. The model con-siders the evolution of the parameters in function of traffic accumulation and material degradation. Different types of maintenance are considered in this model, including their specific consequences to the track structure. For a certain scenario defined by initial operational, structural and geometric conditions, the structural and geometric parameters are calculated over time. Therefore, the number of maintenances is determined taking into account the different maintenance strategies. The costs are calculated from the executed maintenances. The results are presented considering a case study of a heavy haul railway, and in particular for transportation of iron ore material. In the simulation, representative data from a heavy haul scenario for operational and structural conditions are used, in order to determine the impact of load increase on track behavior under two different maintenance strategies. Furthermore, these strategies are evaluated based on their cost and the general impacts on the track structure. A cost analysis is also conducted in a scenario of load increase considering different maintenance strategies and different number of simultaneously working maintenance teams. This analysis with structural and geometric data aims to provide an indication about a maintenance strategy decision and/or procedures to optimize the track performance subjected to high loads.

À propos de ce résultat
Cette page est générée automatiquement et peut contenir des informations qui ne sont pas correctes, complètes, à jour ou pertinentes par rapport à votre recherche. Il en va de même pour toutes les autres pages de ce site. Veillez à vérifier les informations auprès des sources officielles de l'EPFL.
Concepts associés (38)
Voie ferrée
Une voie ferrée est un chemin de roulement pour trains constitué de deux files de rails dont l'écartement est maintenu constant par une fixation sur des traverses, reposant elles-mêmes sur du ballast. Le terme de voie ferrée apparait à partir du en Angleterre et désigne à l'époque l'agencement de deux rails de bois parallèles sur lesquels un cheval tracte une cargaison, ce qui augmente la vitesse du transport.
Track geometry
Track geometry is concerned with the properties and relations of points, lines, curves, and surfaces in the three-dimensional positioning of railroad track. The term is also applied to measurements used in design, construction and maintenance of track. Track geometry involves standards, speed limits and other regulations in the areas of track gauge, alignment, elevation, curvature and track surface. Standards are usually separately expressed for horizontal and vertical layouts although track geometry is three-dimensional.
Tramway track
Tramway track is used on tramways or light rail operations. Grooved rails (or ) are often used to provide a protective flangeway in the trackwork in city streets. Like standard rail tracks, tram tracks consist of two parallel steel rails. Tram rails can be placed on several surfaces, such as with on sleepers like railway tracks, or with grooved rails on concrete sleepers into street surfaces (pavement) for street running. Tram rails in street have the disadvantage that they pose a risk to cyclists.
Afficher plus
Publications associées (33)

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...
2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...
EPFL2024

Analysis of barrette foundations subjected to mechanical and thermal loads

Lyesse Laloui, Alessandro Francesco Rotta Loria

In recent years, there has been increasing interest in the use of rectangular barrette foundations for the structural support and energy supply of tall buildings when circular piles become inefficient or uneconomical. In such applications, so-called energy ...
ELSEVIER2022
Afficher plus
MOOCs associés (1)
L'Art des Structures I - Câbles et arcs
L'art des structures propose une découverte du fonctionnement des structures porteuses, telles que les bâtiments, les toitures ou les ponts. Ce cours présente les principes du dimensionnement et les s

Graph Chatbot

Chattez avec Graph Search

Posez n’importe quelle question sur les cours, conférences, exercices, recherches, actualités, etc. de l’EPFL ou essayez les exemples de questions ci-dessous.

AVERTISSEMENT : Le chatbot Graph n'est pas programmé pour fournir des réponses explicites ou catégoriques à vos questions. Il transforme plutôt vos questions en demandes API qui sont distribuées aux différents services informatiques officiellement administrés par l'EPFL. Son but est uniquement de collecter et de recommander des références pertinentes à des contenus que vous pouvez explorer pour vous aider à répondre à vos questions.