III-V Nanowire Hetero-junction Tunnel FETs integrated on Si

In the last decade the power consumption of electronic devices has increased for both static and active components. Following the Dennard's scaling rule, as long as the transistor sizes are reduced then the supply voltage (VDD) can also be scaled in order to increase the area density and maintain or improve the performances. However, scaling VDD and thus shifting the threshold voltage (Vth) of 60mV in a metal-oxide semiconductor field-effect transistor (MOSFET) increases the OFF state current (Ioff ) by a factor of 10 in the ideal case. The reason for this is that the inverse subthreshold slope (SS) in an ideal MOSFET is limited by the thermionic emission of electrons over a potential barrier, which has an intrinsic physical limit of 60mV/decade. To overcome this limit, novel device concepts have been proposed and the tunnel field-effect transistor (TFET) is one of the most promising because it resembles a MOSFET and should enable to achieve sub-60mV/dec SS, low Ioff and small VDD. The aim of this thesis is to investigate the potential of TFETs by the fabrication and characterization of InAs/Si as p-channel and InAs/GaSb as n-channel device for a complementary TFET technology. III-V nanowires are grown via metal-organic chemical vapor deposition (MOCVD) and are integrated on Si(100) substrates using a novel technique called template-assisted selective epitaxy (TASE), which enables the fabrication of vertical and lateral III-V hetero-structure TFETs. Sub-40nm nanowire cross-section InAs/Si p-TFETs and InAs/GaSb n-TFETs in-plane on Si are demonstrated for the first time. The InAs/Si p-TFETs exhibit state-of-the art performances with an ON state current (Ion) of 4uA/um at VGS=VDS=-0.5V, ON/OFF ratio of 1x10E5 with SSavg of 70-80mV/dec at room temperature. The InAs/GaSb n-TFETs have an order of magnitude larger Ion but the SS is limited by the non-optimized gate-stack on InAs channel and by the depletion of the undoped GaSb source. Different operation regimes of TFETs are investigated by temperature-dependent measurements,Wentzel-Kramers-Brillouin (WKB) modeling and TCAD simulations, indicating that the switching region for InAs/Si is dominated by the presence of traps at the hetero-junction. The abruptness of the band-edges in InAs/GaSb is studied by the extraction of the conductance slope in fabricated p-n and p-i-n tunnel diodes.

From All-Si Nanowire TFETs Towards III-V TFETs

Hesham Ghoneim

Performance improvement by device scaling has been the prevailing method in the semiconductor industry over the past four decades. However, current silicon transistor technology is approaching a fundamental limit where scaling does not improve device performance. As the density of number of devices increases a rise in dynamic and especially static power dissipation is ever more present, making this the biggest issue in microelectronics today. Planar silicon devices are therefore already being replaced by multiple-gate architectures and will be replaced by new channel materials and new switching mechanisms during the next 10 years. A means to decrease the threshold and supply voltage and, therefore minimizing power dissipation, is to employ devices which exhibit a steeper slope than the MOSFET limit of 60 mV/dec at room temperature. The Tunnel FET promises steep turn-on characteristics and low leakage currents as compared to MOSFETs which make it attractive for low-power operation. A great deal of work over the past years has been done to boost device performance of Tunnel FETs by combining ultimate wrap-gate architectures, incorporation of III/V materials and band engineering for hetero-tunnel junctions. The latter is seen as an ideal route towards achieving high drive currents and steep sub-threshold slopes at low supply voltages. This thesis investigates both Si Tunnel FETs and the route towards heterostructure Tunnel FETs, but also the technological challenges to achieve these device structures. The first part of this work deals with vapor-liquid-solid grown silicon in-situ doped n+-i-p nanowire Tunnel FETs in a lateral geometry, where the influence of the gate dielectric, i.e., SiO2 or HfO2, on device performance is investigated along with the study of low-temperature behavior. The devices having the strongest gate coupling due to the high-κ gate oxide HfO2 are shown to exhibit the best device performance as compared with the SiO2 gate stack. A vertical process for Si FETs is developed and improved to obtain a fully wrap-gate geometry. It is adaptable to different material systems and is the basis for the ongoing work on InAs-on-Si nanowire Tunnel FETs. Improved performance for these heterostructure devices requires in particular high doping concentrations as well as abrupt doping profiles to achieve high tunnel currents. Therefore, the second part focuses on the InAs material system and specifically the study of dopant incorporation. Doping is done in-situ using different precursors during growth. The InAs nanowires are grown in SiO2 mask openings on 〈111〉 Si substrates in a metal-organic vapor phase epitaxy process. The effect of the dopants and growth parameters on radial and vertical growth rates, wire morphology and resistivity is investigated. A method utilizing the measured Seebeck coefficient of the InAs nanowires to extract doping densities without the need of assuming a mobility value is presented. Two other reference methods where I-V characteristics of homo-and heterojunction InAs tunnel diodes are fitted by TCAD simulations confirm this approach. Doping densities ranging from 1·1017 cm−3 to 7.1·1019 cm−3 were achieved which is comparable to the highest doping concentration reported in bulk InAs. Furthermore, single vertical pn+-junctions are fabricated by growing n-type InAs nanowires on p-type InAs substrates, which show high tunnel current densities of 500 kA/cm2 at 0.3 V reverse bias. In the forward direction, negative differential resistance is obtained below 200 K, which is the characteristic feature of an Esaki diode.

EPFL2012

Modélisation physique d'un transistor de puissance IGBT

Serge Pittet

The IGBT transistor, associating the conduction advantages of the bipolar transistor and the switching advantages of the MOSFET transistor, is widely used in medium and high power applications with an operating voltage of 1.2kV to 4.5kV. New topologies, reducing the losses in the semi-conductor devices, are often proposed and have to be validated through a simulation tool. The finite element method (FEM) simulators accurately analyse losses in components, but the associated simulation time is so long that they cannot be used for complex topologies in power electronics. An equivalent transistor macromodel, correctly and quickly predicting currents and voltages on the element is needed. This thesis proposes an IGBT transistor model based on semiconductor physics and validated through a comparison with finite element simulator results. The model yields very good results regardless of transistor load and operating point. Base conduction is modelled using a novel equivalent charge approach. This results in a relatively simple macromodel with a good representation of the static and dynamic phenomena. The solving method of the Poisson equation has been revisited to fit recent changes of the internal structure of IGBT transistors. All approximations have been validated through fi- nite element analysis using an appropriate simulation set. The approximation of the internal MOSFET, even though based on existing models, takes into account the specificities of the IGBT transistor structure. It shows the degenerated properties of the internal MOSFET compared to the properties of a standard MOSFET, regardless of the operating point. Using intermediate potentials within the semiconductor structure allows a separate analysis of the different voltage contributions. A complete IGBT transistor macromodel has been developed and tested in different power electronics structures. Good results were obtained in all the tested structures with the proposed IGBT transistor macromodel. Parameter extraction can easily be automated using a mathematical tool such as Matlab and only requires few measurements on the device. The obtained results can then be quickly adapted to an other IGBT device.

EPFL2005

Field-Effect Transistors Based on ZnO Nanowires

Daniel Dominik Kälblein

Semiconductor nanowires are an emerging class of materials with great potential for applications in future electronic devices. The small footprint and the large charge-carrier mobilities of nanowires make them potentially useful for applications with high-integration density, but also to replace thin-film transistors in large-area electronics. This thesis investigates the use of wet-chemically grown ZnO nanowires for the fabrication of high-performance, low-voltage field-effect transistors (FETs). The first part of this thesis addresses the electrical characteristics of the wet-chemically grown ZnO nanowires. The as-grown ZnO nanowires are highly conductive due to a large charge-carrier concentration caused by dopants unintentionally incorporated into the ZnO nanowires during the synthesis. This large charge-carrier concentration makes it difficult to modulate the conductivity of the nanowires by an external electric field, so that the as-grown wires are not suitable for FETs. A post-growth annealing step is employed to dramatically reduce the charge-carrier concentration of the nanowires which makes it possible to fabricate FETs with useful characteristics. ZnO-nanowire FETs in a global back-gate geometry based on annealed ZnO nanowires have a transconductance of 300 nS, an on/off current ratio of 107 and a subthrehold slope of 500 mV/decade. The maximum field-effect mobility of the annealed ZnO nanowires is around 50 cm2/Vs. An important requirement to obtain good FET characterisitcs is to minimize the influence of the source and drain contact resistance on the total device resistance. The material used for the source and drain contacts in this thesis is aluminum. It is demonstrated that the use of a plasma treatment in the contact regions prior to the evaporation of the aluminum contacts can greatly influence the contact properties between ZnO and aluminum. An argon-plasma treatment locally increases the charge-carrier concentration in the ZnO. It is shown that the doping effect of the argon-plasma treatment can be exploited to reduce the contact resistance between alumiunm and ZnO and improve the electrical performance of the FETs. In the second part of this thesis, the influence of the ambient air on the electrical characteristics of the ZnO-nanowire FETs is investigated. The electrical conductivity of the FETs is strongly affected by the distinct atmospheric conditions, which makes it difficult to obtain reliable FET characteristics. The potential of a self-assembled monolayer (SAM) based on fluoroalkylphosphonic acid molecules to passivate the ZnO nanowires against the undesirable effects of the ambient and to stabilize the electrical performance of ZnO-nanowire FETs is demonstrated. The stabilizing effect is attributed to the formation of a densely packed, hydrophobic SAM on the surface of ZnO and aluminum oxide. The quality of the hydrophobic SAMs is confirmed by means of water-contact-angle measurements on SAM-covered ZnO single crystals that show a contact angle of more than 110°. The third part of this thesis is dedicated to the fabrication of high-performance ZnO-nanowire FETs with patterned metal top-gate electrodes. A top-gate fabrication process is developed that uses a very thin gate dielectric consisting only of an alkylphosphonic acid SAM that can be deposited from solution. The insulating quality of the SAM is investigated for top-gate FETs that utilize either gold or aluminum for the top-gate electrode. Gold top-gate FETs show a transconductance of 1 µS, an on/off current ratio of 107, and a steep subthreshold slope of 90 mV/decade. The thin gate dielectric makes it possible to operate the gold top-gate FETs at low voltages of 1 V and simultaneously reduces the undesired gate current by more than three orders of magnitude compared to gold top-gate FETs that have been fabricated without a gate dielectric (MESFETs). The gate current of the gold top-gate FETs with SAM gate dielectric is as low as 1 pA for gate-source voltages between -1 V and 0.5 V. When aluminum is used for the top-gate electrode, a hybrid dielectric is formed at the interface between the SAM and the aluminum, consisting of the SAM and a spontaneously formed aluminum oxide layer. Owing to the hybrid gate dielectric, the aluminum top-gate FETs are operated with gate currents below 1 pA for voltages up to 3 V. The top-gate fabrication process does not require temperatures above 160 °C, which makes it possible to fabricate FETs on unconventional substrates that cannot tolerate high temperatures, such as glass or flexible plastics. Integrated circuits on single ZnO nanowires that are fabricated on glass and plastic substrates are demonstrated. The maximum switching frequency of the inverters is 1 MHz.

EPFL2011