Compositional Characterization of Organo-Lead tri-Halide Perovskite Solar Cells

Perovskite photovoltaics is one of the fastest growing research fields in materials science. Apart from photovoltaics, a wide range of energy-related research fields have gained substan-tial new momentum owing to the fantastic optoelectronic properties of hybrid lead halide per-ovskites. Starting with solar cells showing a mere 3% power conversion efficiency in 2009, researchers have been able to increase this value to over 22% in 2017, comparable to the best monocrystalline silicon solar cells. These improvements are chiefly due to the compositional tuning and mixing of the ABX3 perovskite structure. However, this strategy increases not only the efficiency but also in the same time the complexity of the perovskite formulation. Differ-ent phases, from the nano- to macroscale, can potentially form. In order to rationalize the effi-ciency progress, one needs to understand and characterize the complex perovskite composi-tion and crystal structure in great detail. The main focus of this thesis lies in the in-depth compositional and phase analysis of perovskite thin films as well as full perovskite solar cells, trying to rationalize the consequences of A cation and X anion tuning and mixing. In the first part, it is shown that fabricating solar cells from a non-stoichiometric perovskite precursor composition, namely one with PbI2 excess, leads to increased grain size, enhanced cristallinity, reduced recombination as well as an improved TiO2/perovskite interface. As op-posed to lead iodide phases resulting from film degradation, which is hampering device per-formance, unreacted excess PbI2 phases originating from an excess of PbI2 in the precursor solution are very beneficial for the final solar cell efficiency, reproducibility and stability. The next scientific challenge adressed in this thesis is related to the nano- and microscale composition of the record-breaking mixed cation/mixed anion perovskite composition. Mac-roscale investigations have previously suggested that this formulation results in a single ho-mogenous phase. However, using nanoscale elemental and charge carrier distribution mapping as well as microscale structural and optical film analysis, it is here found that in high efficient solar cells partial phase segregation does take place at the micro- and nanoscale. Moreover, it is shown that mixed cation/anion formulations allow the formation of never re-ported 3D hexagonal lead halide perovskite polytypes, namely 4H and 6H. These polytypes are shown to play a key role during the crystallization process, which is also revealed for the first time here. Indeed, mixed cation/mixed anion perovskite films are fabricated via the crys-tallization sequence 2Hï 4Hï 6Hï 3R(3C). It is demonstrated that the complex crystalliza-tion via these defect-prone hexagonal intermediates can be by-passed by the incorporaton of low amounts of Cs+ cations into the structure. This can explain the improved stability as well as the increased power conversion efficiency and device reproducibility. It gives for the first time a rational explanation as to why the halide perovskite community rapidly adopted the incorporation of Cs+ in mixed perovskites. The last results presented in this thesis are related to the hole-transporting materials (HTM) used in perovskite solar cells. It is shown that carbazole-based small molecule HTMs are a cheap and efficient alternative to the much costlier commercial spiro-OMeTAD.

Strategies to Optimizing Dye-Sensitized Solar Cells

Sophie Wenger

Dye-sensitized solar cells (DSCs) constitute a novel class of hybrid organic-inorganic solar cells. At the heart of the device is a mesoporous film of titanium dioxide (TiO2) nanoparticles, which are coated with a monolayer of dye sensitive to the visible region of the solar spectrum. The role of the dye is similar to the role of chlorophyll in plants; it harvests solar light and transfers the energy via electron transfer to a suitable material (here TiO2) to produce electricity — as opposed to chemical energy in plants. DSCs are fabricated of abundant and cheap materials using inexpensive processes (e.g. screen-printing) and are likely to be a significant contributor to the future commercial photovoltaic technology portfolio. The work conducted during this thesis aimed at optimizing the DSC using three different strategies: The use of versatile organic sensitizers for stable and efficient DSCs, the study of tandem device architectures in combination with other solar cells to harvest a larger fraction of the solar spectrum, and the development of a validated optoelectric model of the DSC. Organic donor-π-acceptor dyes are an interesting alternative to the standard metal-organic complexes used in DSCs. Efficient photovoltaic conversion and stable performance could be demonstrated with three classes of donor systems, namely diphenylamine, difluorenylaminophenyl, and π-extended tetrathiafulvalene. The highest conversion efficiencies were obtained with a difluorenylaminophenyl donor system (η = 8.3 % with a volatile electrolyte and η = 7.6 % with a solvent-free ionic liquid, which was a new record for organic dyes at the time of publication). Surprisingly, efficient regeneration of the oxidized dye by the I-/I3- redox mediator was found with the π-extended tetrathiafulvalene system, even though the thermodynamic driving force was as low as 150 mV. So far driving forces of 300-500 mV had been regarded as necessary for efficient regeneration of the dye cation. Also, important structure-property relationships pertaining to the recombination of electrons with the electrolyte and to the stability of the device could be identified (i.e. effect of linear vs. branched structure, linker length, and moieties used). The power conversion efficiency of solar cells can be extended beyond the limit for a single cell (∼ 30 %) by using multiple cells with different optical gaps in a tandem device. DSCs and chalcopyrite Cu(In,Ga)Se2 (CIGS) solar cells have complementary optical gaps and are thus suitable systems for integration in a tandem device. It was shown that a monolithic DSC/CIGS tandem device has the potential for increased efficiency over a mechanically stacked device due to increased light transmission to the bottom cell, and a monolithic DSC/CIGS device with an initial efficiency of η = 12.2 % was demonstrated. The degradation of the devices — induced by the corrosion of the CIGS cell in contact with the I-/I3- redox mediator — could be retarded with a protective thin conformal ZnO/TiO2 oxide layer coated on the CIGS cell by atomic layer deposition. Finally, an experimentally validated optical and electrical model of the DSC has been developed to assist the optimization process, which is predominantly conducted by empirical means in the DSC research community. The optical model allows to accurately calculate the internal quantum efficiency of devices, i.e. the ratio of extracted electrons to absorbed photons by the dye, a crucial and so far difficult to determine characteristic. Intrinsic parameters — like injection efficiency, electron diffusion length, or distribution of trap states in the TiO2 — can be extracted from experimental steady-state and time-dependent data with the electric model. The model allows to make a comprehensive and quantitative loss analysis of the different optical and electric loss channels in the DSC. The model has been implemented with a graphical user interface for straightforward usage. All three optimization strategies — organic dyes, tandem architecture, and device modeling — developed during this thesis make a valuable contribution to the development and commercialization of inexpensive and high efficiency DSCs. They enable a comprehensive view of the system and pave the way for a systematic analysis and reduction of losses, which has been the ultimate route to success for several established photovoltaic technologies.

EPFL2010

Investigation on the impact of passivation in perovskite solar cells

Erfan Shirzadi

Conversion of sunlight to electricity is the most plausible approach towards the generation of renewable energies. During recent decade lead halide perovskites (LHPs) have proven to be promising candidates for photovoltaic applications such as solar cells. LHPs can be made easily in laboratories around the world via solution process methods and many universities can afford to participate in their development. How-ever, LHPs suffer from instability issues and their efficiencies can be further improved. In this thesis, both instability and efficiency challenges are addressed. We showed by doping the precursor of methylammonium lead iodide (MAPbI3) perovskite with a relatively large cation of 2-Choloroethylammonium (CLEA), perovskites films with CLEA incorporated into their structures are formed. The novel perovskite is able to withstand high temperatures as high as 80°C while achieving efficiencies > 19% in MAPbI3-based perovskite solar cells (PSCs). Various approaches have been employed for the passivation of the defects in perovskite solar cells Vari-ous approaches have been employed to passivate the defects in perovskite films used in perovskite solar cells (PSCs). However, the passivation mechanism is often unclear at a molecular level and the reason for enhanced PSC performance remains elusive. Here, we describe passivation based on the deposition of two dimensional (2D) perovskites (obtained from para-halophenylethylammonium iodide) on the surface of perovskite films. Moreover, the mechanism of passivation was elucidated and was traced to the high work function of the 2D perovskites, which induce band-bending at the surface of perovskite film and therefore reduces the charge carrier recombination at the interface of perovskite and the hole transporting material (HTM). Efficiencies >22% with average voltages >1.15 V were achieved using a typical mesoporous-TiO2 and Spiro-OMeTAD device configuration. This study paves the way for PSCs efficiency improvement by rational design. The employment of 2D perovskites is a promising approach to tackle the stability and voltage issues inherent in perovskite solar cells. It remains unclear however whether other perovskites with different dimensionalities have the same effect on efficiency and stability. Here, we report the use of quasi-3D azetidinium lead iodide (AzPbI3) as a secondary layer on top of the primary 3D perovskite film that results in significant improvements in the photovoltaic parameters. Remarkably, utilization of AzPbI3 leads to the passivation resulting in a power conversion efficiency (PCE) of 22.4 %. The open-circuit voltage obtained is as high as 1.18 V, which is among the highest reported to date for single-junction perovskite solar cells, corresponding to a voltage deficit of 0.37 V for a bandgap of 1.55 eV. Studying the compositional instability of mixed ion perovskites under light illumination is important to understand the mechanisms underlying their efficiency and stability. However, current techniques are limited in resolution and are unable to deconvolute minor ion migration phenomena. Here, we describe a method that enables ion migration to be studied allowing different segregation mechanisms to be elucidated. We applied statistical analysis to cathodoluminescence data to generate compositional distribution histograms. Using these histograms, we identified two different ion migration phenomena, horizontal ion migration (HIM) and vertical ion migration (

EPFL2021

Material Development for Perovskite/Silicon Tandem Photovoltaics

Peter Joseph Fiala

The developed world is built on the fact that energy is readily available and functionally infinite. The electricity from the wall, the gas at the station, and the heat in our homes are reliable and low-cost. But this comfort is so far only possible through the combustion of fossilized carbon sources. This is not a sustainable system. Not only are these sources finite, but the long-term effects of this much combustion are catastrophic for our planet and species. Transitioning from current energy production to sustainable sources will require the development and deployment of a diverse group of technologies. Chief among these is the generation of electricity from sunlight, or photovoltaics (PV).Most modern PV is based on crystalline silicon. Silicon PV alone could be scaled to provide the necessary energy production, but this could be realized more quickly and efficiently if more advanced technologies are used. The defining metric is the cost per generated electricity. In the case of silicon, the current cost breakdown of materials, manufacturing, installation, and system costs leaves little room for further price reduction; and light-to-electricity efficiencies are near their practical limit. Of the proposed alternatives, the pairing of silicon with a thin film of lead-halide perovskite in a multijunction or "tandem" architecture is one of the most promising. This splits the solar spectrum in two, and raises the theoretical maximum efficiency from 33.3% to 45.1% based on each material better using its segment than any one material could use the full spectrum. The central goal of this thesis was therefore to advance the capability of this type of solar cell while remaining within the constraints of industrially-plausible production methods.Towards this goal, we first isolated perovskite layers to study what limits their performance. This led to improvements in the bulk material quality, the interfaces with adjacent materials, and the layer morphology. We reduced bulk disorder via balancing the annealing temperature, time, and environment. The interfaces were improved by selecting passivating materials which were compatible with our deposition methods. We further observed a complex interplay between the materials used and the environment of the annealing, which illuminated critical dependencies of device performance and gave us a more complete understanding of our material. Finally the morphology was improved via high-temperature annealing. This was enabled by a surface-binding additive which reduced the detrimental effects of such an anneal while preserving the benefits, resulting in a perovskite with less internal resistance. From there, we moved outside of the perovskite layer and developed a light scattering ZnO layer which increased the optical performance and absorption of our cells. Returning to the main goal of the thesis, the lessons learned from work on isolated perovskites were applied in tandems on textured silicon. We additionally increased the perovskite layer thickness and made the bottom-cell more robust to processing damages. Together, the result was a stabilized efficiency of 27.3%. This is better than any silicon cell to date, but work remains to achieve 30% and beyond, extend material stability, scale up the deposition area, and transfer these capabilities to industry. Together, the work done as a part of this thesis represents a step forward in the journey towards carbon-neutral energy production.

EPFL2022