Increasing efficiency of perovskite solar cells using low concentrating photovoltaic systems

Perovskite solar cell (PSC) technology is the flag bearer for the future of photovoltaics allowing unlimited possibilities for its application. This technology is currently limited by issues related to its scale-up, stability and the composition of the materials used in its preparation. Using small sized solar cells with higher efficiency under solar concentration is gaining traction as a methodology for scaling up this technology and broadening its applications. However, this has only been reported in devices with size

The emergence of concentrator photovoltaics for perovskite solar cells

Mohammad Khaja Nazeeruddin, Anurag Roy

The emergence of high-efficiency photovoltaic research is undergoing intense study and is technologically desirable to meet sustainable energy and environmental demand. However, every single solar cell has a theoretical power conversion efficiency limit, and, thus, without compromising the cost, the power conversion efficiency enhancement of a solar cell is highly challenging. As a convenient solution, concentrating photovoltaics can focus sunlight onto an extremely high-efficiency solar cell integrating various optics. Concentrating photovoltaics use optical devices that collect and redirect the light toward the smaller photovoltaic cell and reduce the demand for the mined elements required for the solar cell fabrication. The research interest from the photovoltaic community has concentrated on organic-inorganic hybrid halide perovskite absorbers, and nowadays, perovskite solar cells manifest their outstanding contribution among the low-cost photovoltaic technologies. Inevitably, large-area perovskite solar cells suffer a lot with their poor stability, hindering their commercialization pace. Thus, the implementation of concentrating photovoltaic technology in perovskite solar cells demonstrates an inherent advantage using a smaller size solar cell. This review provides an overview of concentrating photovoltaic technology implementation, including their recent research and development portfolio, their economic benefits in combination with inexpensive optical elements and tracking systems, limitations, challenges, and relative scope of the future study, focusing on the emerging perovskite solar cell technology.

AIP Publishing2021

Interface engineering in solid-state dye-sensitized solar cells

Jessica Krüger

Dye-sensitised nanocrystalline solar cells are currently subject of intense research in the framework of renewable energies as a low-cost photovoltaic device. In particular dye-sensitised cells based on spiro-MeOTAD have gained attention as promising approach towards an organic solid-state solar cell. However, the efficiency in such dye-sensitised solid-state solar devices (SSD) was so far only ca. 10 % of the values reported at AM1.5 for the classical dye-sensitised solar cell with an electrolyte hole transporting medium (DSSC). The objective of the present work is to study the limitations that emerge from the exchange of the electrolyte by the solid-state system and that oppose photovoltaic photon-to-electron conversion as high as for the DSSC. Interfacial charge recombination is an important loss mechanism in dye-sensitised solar cells. This is particularly true for SSD, as the solid hole-transporting medium is less efficient in screening of internal fields which assist recombination. A variety of strategies were tested in the SSD to minimise interfacial charge recombination. The most promising approach was the blending of the hole-transporting medium with tert.-butylpyridine (tBP) and lithium ions. Optical and electrochemical techniques, such as nanosecond laser spectroscopy, impedance spectroscopy and photovoltaic characterisation measurements, were used to study the impact of the additives on the SSD. Both lithium ions as well as tBP were found to increase the open circuit potential of the SSD. At the same time tBP was found to considerably lower the current output. The interaction of the additives was studied and their concentration in the spiro-MeOTAD medium optimised. The doping of the spiro-MeOTAD film, which was intended to support the hole transport, was found to enhance interfacial recombination significantly. The morphological properties of the TiO2, in particular layer thickness, particle size and film porosity, play a more important role in the SSD than in the DSSC. Penetration of the hole conductor into the TiO2 pores and electron diffusion length are coupled to these properties. As a result the light harvesting cannot be controlled at will via the TiO2 film thickness and the active surface area for dye adsorption. An enhanced light harvesting for thin TiO2 layers offers advantages for the charge transport and the formation of the interpenetrating network. The dye uptake in presence of silver ions was found to increase the dye loading and to significantly improve the device performance of thin TiO2 layer devices. The mechanism of this simple dye modification technique was studied by a variety of spectroscopic techniques. From spectroscopic evidence it is inferred that the silver is binding to the sensitiser via the ambidentate thiocyanate, allowing the formation of ligand-bridged dye complexes. The beneficial influence of the silver ions on the photovoltaic performance was not limited to the application of the standard N3 dye nor to the spiro-MeOTAD. SSDs were furthermore studied by frequency resolved techniques. Intensity modulated photocurrent spectroscopy (IMPS) and intensity modulated photovoltage spectroscopy (IMVS) were performed over a wide range of illumination intensities. The IMPS and IMVS responses provide information about charge transport and electron-hole recombination processes respectively. For the range of light intensities investigated, the dynamic photocurrent response appears to be limited by the transport of electrons in the nanocrystalline TiO2 film rather than by the transport of holes in the spiro-MeOTAD. The diffusion length of electrons in the TiO2 was found to be 4.4 μm. This value was almost independent of the light intensity as a consequence of the fact that the electron diffusion coefficient and the rate constant for electron-hole recombination both increase in the same way with light intensity but with opposite sign. The results of this work provide for a substantial improvement of the overall photovoltaic performance compared to earlier results for this type of SSD. However, this study reveals also that high conversion efficiencies as are measured for DSSC are not likely to be reachable with the spiro-MeOTAD system due to the significantly slower charge transport in the spiro-MeOTAD compared to the electrolyte redox mediator.

EPFL2003

Monte Carlo simulations of quantum dot solar concentrators: ray tracing based on fluorescence mapping

Charu Datta Galande, André Gabriel Kostro, Jean-Louis Scartezzini, Andreas Schueler

One promising application of semiconductor nanostructures in the field of photovoltaics might be quantum dot solar concentrators. Quantum dot containing nanocomposite thin films are synthesized at EPFL-LESO by a low cost sol-gel process. In order to study the potential of the novel planar photoluminescent concentrators, reliable computer simulations are needed. A computer code for ray tracing simulations of quantum dot solar concentrators has been developed at EPFL-LESO on the basis of Monte Carlo methods that are applied to polarization-dependent reflection/transmission at interfaces, photon absorption by the semiconductor nanocrystals and photoluminescent reemission. The software allows importing measured or theoretical absorption/reemission spectra describing the photoluminescent properties of the quantum dots. Hereby the properties of photoluminescent reemission are described by a set of emission spectra depending on the energy of the incoming photon, allowing to simulate the photoluminescent emission using the inverse function method. By our simulations, the importance of two main factors is revealed, an emission spectrum matched to the spectral efficiency curve of the photovoltaic cell, and a large Stokes shift, which is advantageous for the lateral energy transport. No significant energy losses are implied when the quantum dots are contained within a nanocomposite coating instead of being dispersed in the entire volume of the pane. Together with the knowledge on the optoelectronical properties of suitable photovoltaic cells, the simulations allow to predict the total efficiency of the envisaged concentrating PV systems, and to optimize photoluminescent emission frequencies, optical densities, and pane dimensions. Keywords: quantum dots, photoluminescence, fluorescent planar solar concentrators, photovoltaics, solar cells, Monte Carlo simulations, ray tracing, polarization