Recherche

Afficher tous les résultats pour

Accueil

Publication

Effect of static and kinematic boundary conditions on the out-of-plane response of brick masonry walls

À propos
Confidentialité
Mentions légales

Graph Chatbot

Publications associées (29)

Design of a Flexure-Based Flywheel for the Storage of Angular Momentum and Kinetic Energy

Simon Nessim Henein, Florent Cosandier, Hubert Pierre-Marie Benoît Schneegans, Patrick Robert Flückiger

The flywheel is a widespread mechanical component used for the storage of kinetic energy and angular momentum. It typically consists of cylindrical inertia rotating about its axis on rolling bearings, which involves undesired friction, lubrication, and wea ...

2024

Experimental Investigation on Size-Effect of Rubble Stone Masonry Walls Under In-Plane Horizontal Loading: Overview and Preliminary Results

Katrin Beyer, Savvas Saloustros

Rubble stone masonry is a common construction typology of historical city centres and vernacular architecture. While past earthquakes have shown that it is one of the most vulnerable masonry construction typologies, there are few experimental campaigns giv ...

2024

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Marko Pejatovic

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

EPFL2024

Model uncertainties in action effects and load bearing capacity calculation in statically indeterminate reinforced concrete structures

Aurelio Muttoni, Alain Nussbaumer, Xhemsi Malja

For the dimensioning and assessment of structures, it is common practice to compare action effects with sectional resistances. Extensive studies have been performed to quantify the model uncertainty on the resistance side. However, for statically indetermi ...

Ernst & Sohn2024

Decarbonization potential of steel fibre-reinforced limestone calcined clay cement concrete one-way slabs

Hisham Tarek Mohamed Hafez

This study deals with a comparison of the environmental performance of one-way slabs utilizing steel fibrereinforced limestone calcined clay cement (LC3) concrete with the control case of Ordinary Portland cement concrete. The experimental program constitu ...

Elsevier Sci Ltd2024

Additively manufactured steel reinforcement for small scale reinforced concrete modeling: Tensile and bond behavior

Christian Leinenbach, Rafal Wróbel

Small scale (1:30-1:40) Reinforced Concrete is useful for centrifuge testing. However, manufacturing the reinforcing cages by hand at this scale is practically difficult. This paper suggests that small scale reinforcement can be manufactured using a metal ...

Elsevier Sci Ltd2024

Estimation of the bar stress based on crack width measurements in reinforced concrete structures

Aurelio Muttoni, Enrique Corres Sojo

Estimating the stress of reinforcing bars and its variations in service conditions can be useful to determine the reserve capacity of structures or to assess the risk of fatigue in the reinforcement. This paper investigates the use crack width measurements ...

Ernst & Sohn2024

Experimental testing and structural analysis of composite tile – reinforced concrete domes

Savvas Saloustros

Conventional formworks for concrete curved shells either are expensive, complex and wasteful or have formal restrictions. Using tile vaults (also known as timbrel, Guastavino, thin-tile or Catalan vaults) as stay-in-place formwork for concrete shells could ...

2023

Dynamic Modeling of an Origami Prismatic Joint

Jamie Paik, Mustafa Mete, Jian-Lin Huang

Dynamic modeling of folding joints is critical for predicting dynamic behavior, optimizing design parameters, and developing control strategies for origami robots and machines. Although kinematics of the folded joints exists, little research describes thei ...

IEEE2023

Mechanism balancing taxonomy

Simon Nessim Henein, Florent Cosandier, Hubert Pierre-Marie Benoît Schneegans

The balancing of mechanisms consists in distributing their moving masses, inertias, and elastic components in order to achieve key mechanical properties, such as the elimination of the shaking forces and moments exported onto their supporting structure or ...

2023

Page 2 sur 3

Design of a Flexure-Based Flywheel for the Storage of Angular Momentum and Kinetic Energy

Simon Nessim Henein, Florent Cosandier, Hubert Pierre-Marie Benoît Schneegans, Patrick Robert Flückiger

2024

Experimental Investigation on Size-Effect of Rubble Stone Masonry Walls Under In-Plane Horizontal Loading: Overview and Preliminary Results

Katrin Beyer, Savvas Saloustros

2024

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Marko Pejatovic

EPFL2024

Model uncertainties in action effects and load bearing capacity calculation in statically indeterminate reinforced concrete structures

Aurelio Muttoni, Alain Nussbaumer, Xhemsi Malja

Ernst & Sohn2024