Crossover between distinct symmetries in solid solutions of rare earth nickelates

A strong coupling of the lattice to functional properties is observed in many transition metal oxide systems, such as the ABO(3) perovskites. In the quest for tailor-made materials, it is essential to be able to control the structural properties of the compound(s) of interest. Here, thin film solid solutions that combine NdNiO3 and LaNiO3, two materials with the perovskite structure but distinct space groups, are analyzed. Raman spectroscopy and scanning transmission electron microscopy are combined in a synergistic approach to fully determine the mechanism of the structural crossover with chemical composition. It is found that the symmetry transition is achieved by phase coexistence in a way that depends on the substrate selected. These results carry implications for analog-tuning of physical properties in future functional materials based on these compounds.

Ferroelectric Effects Probed by in situ Transmission Electron Microscopy

Reinis Ignatans

Ferroelectric perovskite oxides are widely used in sensors, actuators and optical modulators and, at the same time, they show promise for implementation in future applications such as energy storage, memory and cooling devices. At the infancy of the discovery of polycrystalline ferroelectrics, BaTiO3 was considered as a candidate for various applications, but the breakthrough for the commercialization of ferroelectrics came in 1952 when the ferroelectric PbZrO3 - PbTiO3 (PZT) solid solution system was discovered. PZT and other lead containing perovskite oxides remained on the forefront of scientific and industrial interest. However, concerns over the environmental and health hazards posed by these toxic materials in the electronic and electrical equipment created a legislation change. Nowadays, all applicable products in the EU must pass RoHS (Restriction of Hazardous Substances also known as Directive 2002/95/EC) compliance. This change in the industrial standards fueled research in lead-free ferroelectric materials once again. Attention is currently placed on materials based on BaTiO3, BaZrO3, (Na/K)NbO3, Na1/2Bi1/2TiO3. Their widespread application is yet to be realized as their physical properties pale in comparison to PZT. Substantial challenges also lie in the miniaturization of polar perovskites where effects at nano and microscopic scales become dominant, which inhibit their performance.In this thesis one of the most prominent lead-free ferroelectric perovskites BaTiO3 is studied by transmission electron microscopy (TEM) techniques in combination with in situ temperature and electric field control. In detail, a reliable focused ion beam sample preparation for in situ TEM electrical biasing for ferroelectrics is established. The method is tested on BaTiO3 at room temperature, where the electrical response is observed at the expected field values, further confirmed by finite element calculations. Domain area (polarization) - applied bias loops are directly measured revealing strong pinning at lower fields, while higher fields depin domain walls allowing for more free movement following Rayleigh's law.Upon increasing the temperature, BaTiO3 exhibits morphological transformations in its domain structure from ferroelectric 180° (close to room temperature) to ferroelastic 90° state (below the Curie temperature). Electrical biasing experiments of ferroelastic needle domains show two different forward growth mechanisms. In one case, the needle domains are shown to move freely, influenced mainly by Peierls-like potentials, while when perpendicular domains meet, their movement is hindered by strong domain domain pinning mediated by electromechanical fields. The latter one produces square shaped P-E like loops with distinct steps, indicative of Barkhausen pulses.Finally, the effect of ferroelectric phase transition on the electronic structure is studied with in situ electron energy loss spectroscopy (EELS) and density functional theory (DFT) calculations. Core-loss EELS measurements show that changes in the Ti 3d states qualitatively agree with DFT calculations. Off-axis low-loss EELS allows precise bandgap measurements in both phases. Custom experimental and data treatment methodologies are developed to retrieve momentum resolved dielectric functions, which show excellent fit with DFT calculated ones at small momentum transfer. A pathway to study oxygen deficient perovskites with EELS is theoretically demonstrated with DFT.

EPFL2022

Toxicity study of nanostructures

Lenke Horváth

The great achievement of nanotechnology is the controlled synthesis of a large variety of nanometer-size materials like needle-formed nanotubes, nanowires and two-dimensional graphene flakes. Due to their unique physico-chemical properties, these nanostructures are considered to be of great benefit for many applications in engineering, electronics, alternative energies and nanomedicine. Since the expectations for the improvement of our everyday life through engineered nanomaterials are high, there is rapid expansion of their manufacturing, which makes it likely that intentional and unintentional human and environmental exposure will increase in the near future. Consequently, the concern grows, related to their possible health hazards, as some of them strongly resemble asbestos. Motivated by this issue, we have investigated the in vitro acute cellular toxicity associated with four model nanomaterials: carbon nanotubes, boron nitride nanotubes, titanium dioxide nanofilaments and graphene oxide. This study focused on the toxic effect these nanomaterials had on cell types found in the respiratory system, where exposure to these materials is most prominent. These are lung epithelial cells, macrophages, and fibroblasts, but also other cell types like kidney cells were tested. The cytotoxicity was assessed by using MTT, DNA and FMCA assays, which measure different endpoints such as metabolic activity, cell proliferation and viable cell number. The cell death was determined by the Annexin V assay. We employed various microscopic techniques: light microscopy to reveal the morphological alterations associated with the nanomaterial toxicity at the cellular level; scanning electron microscopy to study the cell-nanomaterial interactions on the surface of the cell membrane; transmission electron microscopy to examine the uptake and subsequent localization of the nanomaterials within the cytosol and cell organelles. In addition, the generation of intracellular reactive oxygen species induced by graphene oxide was detected by the DCF assay. Last but not least, the pro-inflammatory potential and the biochemical perturbations in cells exposed to boron nitride nanotubes were investigated by Western blot and Synchrotron Infrared Microspectroscopy (SIRMS), respectively. All these techniques point to the adverse effects of the investigated nanostructures: i) The toxic effect of carbon nanotubes and carbon nanoparticles showed a time- and dose-dependent impairment in the metabolic activity of the cells characteristic for each cell type. Moreover, distinct morphological alterations typical for cell death were particularly apparent in macrophages. ii) The toxic potential of boron nitride nanotubes exhibited more pronounced adverse effects than carbon nanotubes. This was demonstrated by cell viability assays combined with cytopathological and biochemical analyses, showing induction of serious morphological changes, particularly in macrophages and fibroblasts, and biochemical processes characteristic for cell death. A higher acute toxicity was determined for boron nitride nanotubes when compared to crocidolite asbestos and their pro-inflammatory potential was demonstrated by the secretion of mature IL-1β cytokine in macrophages. iii) Titanium dioxide nanofilaments were also shown to impair the metabolic activity of the studied cells and induce morphological changes pointing to cell insult. iv) Graphene oxide exhibited a mild cytotoxic action in comparison to carbon nanotubes on epithelial cells and macrophages. The interaction of the nanomaterial with the cell surface generated reactive oxygen species during the initial phase of the exposure and transmission electron microscopy showed that graphene oxide flakes are taken up via the endocytic pathway. In summary, our findings highlight important physico-chemical parameters, which are important in relation to the toxic effect of nanomaterials. These are: i) the chemical composition; ii) the surface modification including functionalized groups and structural defects; iii) the geometry: length, diameter and tortuosity. In addition to the identified nanomaterial characteristics, we pinpoint that the target cells ́ response depends on their type, which is likely to be linked to their physiological function.

EPFL2012

Characterization at the Atomistic Level of Defective Structures in Complex Materials

Piyush Agrawal

Defects are key to enhance or deploy particular materials properties. In this thesis I present analyses of the impact of defects on the electronic structure of materials using combined experimental and theoretical Electron energy loss spectroscopy (EELS) in (Scanning) Transmission Electron Microscopy. The energy loss near-edge structure (ELNES) in EELS reflects the element-specific electronic structure providing insights into bonding characteristics of individual atomic species. New electron optical devices have boosted the analytical capabilities by which materials can be investigated with atomic resolution and single atom sensitivity using (scanning) transmission electron spectroscopy (STEM/TEM).With the help of aberration correctors for forming small electron probes, high intensity electron beams can nowadays be focused to clearly less than 100 pm which has enhanced the resolution and sensitivity in analytical scanning transmission electron microscopy (STEM). Various kinds of defects in different complex oxides were studied: point defects like oxygen vacancies in BiVO4 and SrMnO3, edge-dislocations in BiFeO3, and planar defects in GaAs. By comparison with experimental data, structures for these systems were proposed based on all-electron density functional theory (DFT) code Wien2k. By comparing theoretical calculations and experimental data, a pronounced surface reduction in the oxidation state of vanadium in BiVO4 from +5 to +4 was unveiled, which is due to a high density of oxygen vacancies, and its importance in potential application of BiVO4 in photoelectrochemical energy conversion. A similar study was performed on a series of SrMnO3 thin films with different epitaxial strain where theoretical investigations revealed the impact of oxygen non-stoichiometry and strain on the O-K ELNES. In the next study, molecular dynamics simulations were combined with FEFF-based EELS calculations and its comparison with experiments was helpful for the correct prediction of the edge dislocation core structure in BiFeO3. This study also confirmed the presence of Fe atoms in the core of the edge dislocation which possibly makes these defects ferromagnetic whereas the bulk structure is known to be antiferromagnetic. This thesis has established methodologies for utilizing different codes, illustrating how links between experimental and theoretical ELNES can be used in revealing structural information around defects and how defects affect materials properties. This tandem methodology of theory and experiments is applicable to various future materials where the reliable interpretation of EELS data is pivotal in unfolding mysteries of such technologically important materials.

EPFL2017