Publications associées à Assessing the degradation of compliant electrodes for soft actuators

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Tara Habibi, Landolf-Giosef-Anastasios Rhode-Barbarigos

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Highly anisotropic carbon fiber electrodes for DEAs and their dynamic non-monotonic conductive properties

Yves Perriard, Stefania Maria Aliki Konstantinidi, Markus Koenigsdorff

A common method for creating compliant electrodes for dielectric elastomer actuators (DEAs) and soft sensors is to incorporate electrically conductive carbon particles into a polymer matrix. However, using unidirectional aligned carbon fibers instead not o ...

Society of Photo-Optical Instrumentation Engineers (SPIE)2024

Inversing the actuation cycle of dielectric elastomer actuators for a facial prosthesis

Yves Perriard, Yoan René Cyrille Civet, Paolo Germano, Alexis Boegli, Thomas Guillaume Martinez, Stefania Maria Aliki Konstantinidi, Quentin Philippe Mario De Menech

Dielectric Elastomer Actuators (DEAs) are a type of smart material described as compliant capacitors. They show impressive performances as soft actuators, such as a high strain and fast response. Nonetheless, replicating natural muscle function with DEAs h ...

Society of Photo-Optical Instrumentation Engineers (SPIE)2024

Modeling friction and wear using an adaptive discrete-continuum coupling

Manon Eugénie Voisin--Leprince

When two objects slide against each other, wear and friction occur at their interface. The accumulation of wear forms what is commonly referred to as a ``third-body''. Understanding third-body evolution has significant applications in industry, where contr ...

EPFL2024

Carbon based printed electrodes for DEAs: study of pad, inkjet, and stencil printing

Yves Perriard, Yoan René Cyrille Civet, Thomas Guillaume Martinez, Stefania Maria Aliki Konstantinidi, Armando Matthieu Walter, Simon Holzer

Dielectric elastomer actuators (DEAs) have raised interest due to their remarkable capabilities in various applications, such as soft robotics, haptic feedback systems, and biomedical devices. To harness the full potential of DEAs, the choice of the electr ...

Society of Photo-Optical Instrumentation Engineers (SPIE)2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Insights from an extensive triaxial testing campaign on a shale for comparative site characterization of a deep geological repository

Lyesse Laloui, Alessio Ferrari, Eleonora Crisci

Several boreholes were drilled for site comparison of a deep geological repository (DGR) in Northern Switzerland. The main target of the exploration program was the >100m thick Opalinus Clay, the designated host rock encountered at approximately 450 to 100 ...

Elsevier2024

Strain engineering and strain measurement by spring tethers on suspended epitaxial GaN-on-Si photonic crystal devices

Romuald Houdré, Jun Wang

Suspended epitaxial gallium nitride (GaN) on silicon (Si) photonic crystal devices suffer from large residual tensile strain, especially for long waveguides, because fine structures tend to crack due to large stress. By introducing spring-like tethers, des ...

Iop Publishing Ltd2024

Permanently magnetized elastomer rotating actuator using traveling waves

Herbert Shea

We report a soft actuator that generates continuous rotation of an object placed on it by electromagnetically exciting circular travelling waves in a soft disk. The disk, that serves as the stator, is made of a stretchable composite consisting of segments ...

Iop Publishing Ltd2024

Garment Recovery with Shape and Deformation Priors

Pascal Fua, Benoît Alain René Guillard, Ren Li, Corentin Camille Marius Dumery

While modeling people wearing tight-fitting clothing has made great strides in recent years, loose-fitting clothing remains a challenge. We propose a method that delivers realistic garment models from real-world images, regardless of garment shape or defor ...

2024