Publications associées à Complex image method for RF antenna-plasma inductive coupling calculation in planar geometry. Part I: basic concepts

Modeling and optimization of PCB coils for inductive power transfer systems

The auxiliary power supply for medium voltage converters requires high insulation capability between the source and the load. Inductive power transfer technology, with an air gap between the primary and secondary coil, offers such high insulation capabilit ...

EPFL2024

A Two-Wired High Input Impedance and High CMRR Active Electrode Insensitive to Component Mismatch

Alexandre Schmid, Mehdi Saberi

This article proposes a new two-wired amplifying active electrode (AE), presenting a high input impedance and a high common-mode rejection ratio (CMRR). In the proposed structure, the input impedance and the CMRR of the system are considerably increased by ...

Ieee-Inst Electrical Electronics Engineers Inc2024

Impact of beam-coupling impedance on the Schottky spectrum of bunched beam

Tatiana Pieloni, Nicolas Frank Mounet, Christophe Emmanuel R. Lannoy

The Schottky monitors of the Large Hadron Collider (LHC) can be used for non-invasive beam diagnostics to estimate various bunch characteristics, such as tune, chromaticity, bunch profile or synchrotron frequency distribution. However, collective effects, ...

Iop Publishing Ltd2024

On the use of Cramér-Rao Lower Bound for least-variance circuit parameters identification of Li-ion cells

Mario Paolone, Vladimir Sovljanski

Electrochemical Impedance Spectroscopy (EIS) and Equivalent Circuit Models (ECMs) are widely used to characterize the impedance and estimate parameters of electrochemical systems such as batteries. We use a generic ECM with ten parameters grouped to model ...

2024

Performance Comparison of Cables With Partial Transposition

Pierluigi Bruzzone, Kamil Sedlák, Federica Demattè, Chiara Frittitta

The need of full transposition of the current carrying elements (strands) in large cables is frequently retained as top design criterion for conductors operating in pulsed mode. However, when the transposition error, i.e., the inductance difference among t ...

IEEE Institute of Electrical and Electronics Engineers2024

Enabling Wide Bandwidth in Substrate-Integrated Waveguide Slot Antennas by Using Low-Index Metamaterials

Romain Christophe Rémy Fleury, Amir Jafargholi, Jalaledin Tayebpour

This paper presents a solution to overcome the inherently limited bandwidth of substrate-integrated waveguide (SIW) slot antennas. It is analytically shown that by decreasing the permittivity of a dielectric loaded slot antenna, the resulting bandwidth inc ...

American Physical Society (APS)2024

High-frequency response of a hemispherical grounding electrode

Marcos Rubinstein, Antonio Sunjerga, Farhad Rachidi-Haeri

The lightning discharge current is characterized by a high-frequency spectrum extending from DC to about 10 MHz. The calculation of the grounding impedance is one of the most important aspects of designing lightning protection systems. The search for analy ...

Elsevier2024

DC Power Distribution Networks with Direct Current Transformers

Renan Pillon Barcelos

The shift towards DC power distribution networks, enabled by power electronics technologies, is changing the nature of electrical power systems. Nowadays, DC power distribution networks can effectively support the high penetration of distributed energy res ...

EPFL2024

A modular multiple frequency inductive link to wirelessly power multiple miniaturized implants

Sandro Carrara, Diego Ghezzi, Gian Luca Barbruni

A modular multiple frequency coils inductive link system to wirelessly provide power for at least a medical implant at an output of a receiving coil, whereby the receiving coil is configured to be implanted in an organism. The modular multiple frequency co ...

2024

Characterization of low-temperature plasmas generated by dielectric barrier discharges for bacterial inactivation

Lorenzo Ibba

Low-temperature plasmas (LTPs) at atmospheric pressure hold great promise for disinfection and sterilization applications. When compared to traditional sterilization technologies like autoclaving, LTPs may offer several benefits, including reduced energy c ...

EPFL2024