ISM radio band | EPFL Graph Search

The ISM radio bands are portions of the radio spectrum reserved internationally for industrial, scientific, and medical (ISM) purposes, excluding applications in telecommunications. Examples of applications for the use of radio frequency (RF) energy in these bands include radio-frequency process heating, microwave ovens, and medical diathermy machines. The powerful emissions of these devices can create electromagnetic interference and disrupt radio communication using the same frequency, so these devices are limited to certain bands of frequencies. In general, communications equipment operating in ISM bands must tolerate any interference generated by ISM applications, and users have no regulatory protection from ISM device operation in these bands. Despite the intent of the original allocations, in recent years the fastest-growing use of these bands has been for short-range, low-power wireless communications systems, since these bands are often approved for such devices, which can be used without a government license, as would otherwise be required for transmitters; ISM frequencies are often chosen for this purpose as they already must tolerate interference issues. Cordless phones, Bluetooth devices, near-field communication (NFC) devices, garage door openers, baby monitors, and wireless computer networks (Wi-Fi) may all use the ISM frequencies, although these low-power transmitters are not considered to be ISM devices. The ISM bands are defined by the ITU Radio Regulations (article 5) in footnotes 5.138, 5.150, and 5.280 of the Radio Regulations. Individual countries' use of the bands designated in these sections may differ due to variations in national radio regulations. Because communication devices using the ISM bands must tolerate any interference from ISM equipment, unlicensed operations are typically permitted to use these bands, since unlicensed operation typically needs to be tolerant of interference from other devices anyway.

Broadbeam microstrip patch antenna using higher order modes

Anja Skrivervik, Ismael Vico Triviño

The aim of this contribution is to assess the potential of using various microstrip radiating elements excited with different modes to achieve wide pattern beamwidths. The proposed antenna is made in classic microstrip technology and consists of a circular disk and a ring. The two radiating elements are excited for the TM10 and TM31 modes, respectively. Only the disk is fed, and the ring is connected to the disk through a microstrip line. The proposed antenna is matched at the 2.4GHz industrial, scientific and medical band (ISM) and exhibits a bandwidth of 120MHz. The combination of the two radiating elements achieves a 3dB beamwidth of 160 degrees. The maximum gain is 5.7dBi.

The European Association on Antennas and Propagation (EurAAP)2019

A low-power 2.4 GHz CMOS receiver using BAW resonators

Jérémie Chabloz

It has already been a few years since the first appearance of micro-electromechanical systems (MEMS) in academic research. Since then, a broad number of devices have been designed under this generic term. Bulk-acoustic wave (BAW) resonators are among the few of them which have become exploited at industrial level. They are mainly used to implement filters for mainstream telecommunication applications. In a different domain, potential applications for integrated wireless transceivers are flourishing. While some of them require always higher data rates, others need devices with low data rate but even lower power consumption. The goal of this thesis is to explore ways of using BAW resonators to implement building blocks for such a low-power radio and actually verify the postulate that this could help improving power consumption as well as miniaturize key functionalities. For the active integrated circuit part, the choice of a standard digital 0.18µm CMOS process established itself for its low cost and ubiquity. The specifications for the developed radio receiver are calculated for a physical layer derived from the well known Bluetooth communication protocol in the 2.4GHz ISM band with similar applications scenarii but with much lower data rates and wider channel spacing. After presenting the advantages and limitations of the devices, the implications for using BAWresonators to implement a low-power radio are investigated at circuit and system levels and a super-heterodyne architecture is proposed. A selective low-noise amplifier (LNA) is used at the circuit front-end to yield image and blocker rejection. Measurements for the RF front-end comprising an external balun, the selective LNA, a first downconversionmixer and an intermediate-frequency (IF) amplifier showed an overall noise figure of 11dB for a current consumption of 1.5mA under 1.2V. The high selectivity of the design yields an image rejection ratio of at least 50dB and allows to decrease linearity requirements and thus power consumption. A slightly improved version of the same front-end integrated together with the analog baseband signal processing chain but still using external local oscillators showed sensitivities of -96dBm at 100kbps symbol rate and -93dBm at 200kbps with an external state-of-the art FSK demodulator, allowing to extrapolate a global noise figure of 12.2dB for a global current consumption of 2.3mA under 1.2V. The proposed solution for the frequency synthesis uses both a BAW oscillator for the first downconversion to IF and a quadrature quasi-harmonic relaxation oscillator to translate the signals to baseband. The relaxation oscillator is embedded within a phase-locked loop (PLL) for which all the required blocks are discussed. Particularly, a novel modular multi-modulus frequency divider is presented, which does not necessitate complicated logic to yield the wanted division ratio and uses dynamic logic. The necessary digital circuitry to control the frequency generation is discussed as well. Finally, measurements for the complete receiver using the proposed frequency synthesis as well as digital control and demodulator implemented on FPGA are presented.

EPFL2008