Ultrafast charge separation dynamics in opaque, operational dye-sensitized solar cells revealed by femtosecond diffuse reflectance spectroscopy

Elham Ghadiri, Ulf Anders Hagfeldt, Jacques-Edouard Moser, Shaik Mohammed Zakeeruddin
Nature Publishing Group, 2016
Journal paper

Abstract

Efficient dye-sensitized solar cells are based on highly diffusive mesoscopic layers that render these devices opaque and unsuitable for ultrafast transient absorption spectroscopy measurements in transmission mode. We developed a novel sub-200 femtosecond time-resolved diffuse reflectance spectroscopy scheme combined with potentiostatic control to study various solar cells in fully operational condition. We studied performance optimized devices based on liquid redox electrolytes and opaque TiO2 films, as well as other morphologies, such as TiO2 fibers and nanotubes. Charge injection from the Z907 dye in all TiO2 morphologies was observed to take place in the sub-200 fs time scale. The kinetics of electron-hole back recombination has features in the picosecond to nanosecond time scale. This observation is significantly different from what was reported in the literature where the electron-hole back recombination for transparent films of small particles is generally accepted to occur on a longer time scale of microseconds. The kinetics of the ultrafast electron injection remained unchanged for voltages between +500 mV and –690 mV, where the injection yield eventually drops steeply. The primary charge separation in Y123 organic dye based devices was clearly slower occurring in two picoseconds and no kinetic component on the shorter femtosecond time scale was recorded.

Official source

https://infoscience.epfl.ch/record/218204?ln=en

About this result

This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.

Related concepts

Related publications

Over the past fifteen years dye-sensitised nanocrystalline solar cells have been the subject of intense research and development efforts. These systems provide a technically and economically credible alternative to classical p-n junction solar cells, reaching over 10 % certified efficiency under standard solar illumination conditions (AM 1.5, 1000 W/m2). Recently, the liquid electrolyte, commonly used in these dye-sensitised solar cells, could successfully be replaced by a novel solid hole-conducting material (spiro-OMeTAD). The absence of volatile solvents and corrosive components like iodine presents a clear advantage of these solid-state devices over their photoelectrochemical counterparts. Yet, their maximum overall efficiency of about 3 % clearly lacks behind the performance features of classical dye-sensitized solar cells. The objective of this work is the replacement of the usually used sensitiser (transition metal complexes and organic dyes) by quantum-dots. It was motivated by the possibility to achieve panchromatic light absorption due to the size-dependent properties of the quantum-dots. Some studies have been published using quantum-dots of inorganic low-bandgap semiconductors as sensitisers for mesoporous wide bandgap semiconductor electrodes in conjunction with liquid electrolytes. These systems often suffer from corrosion and photo-corrosion mainly due to the aggressive nature of the electrolyte employed. Solid-state organic-inorganic heterojunctions might provide the desired environment for quantum-dot sensitisation, as the environment is much less aggressive. A large variety of inorganic quantum-dot materials like PbS, CdS, PbSe and CdSe were scrutinized for their use as sensitisers. All particles were synthesised in situ on the TiO2 surface using two different techniques: dip-coating and chemical bath deposition. Lead sulphide was the most investigated due to its superior photovoltaic characteristics. High Resolution Transmission Electron Microscopy (HRTEM) of PbS sensitised TiO2 electrodes fabricated via dip-coating clearly showed the distinct particles on the surface of the semiconductor. The electron transfer dynamics following optical excitation of quantum-dot sensitized TiO2/spiro-OMeTAD heterojunctions were thoroughly studied. Fluorescence spectroscopy was used to prove the possible electron injection from the PbS into the TiO2. Nanosecond laser spectroscopy was applied to monitor the interfacial recombination of the injected electron and the oxidised hole-conductor. Femtosecond laser spectroscopy allowed measuring the ultra-fast kinetics in the system, including electron trapping, exciton recombination and PbS regeneration. An overall efficiency of 0.5 % at 0.1 sun (AM 1.5) has been reached with such systems. Chemical bath deposition (CBD) of PbS leads to the formation of a layer rather than distinct particles on the TiO2. Solar cells fabricated via CBD exhibited open-circuit voltages which were generally 100 mV higher then those of comparable devices made via dip-coating. The PbS layer acts as blocking layer, hindering the contact between TiO2 and the hole-conductor. This technique allowed achieving devices highly linear with respect to the illumination power. Different strategies were pursued to impede interfacial recombination, among which the introduction of self-assembled monolayers at the interface between the organic and inorganic phases was proven to be the most efficient. Nanosecond laser spectroscopy showed a strong decrease of the interfacial recombination kinetic rates in the presence of hexadecylmalonic acid or decylphosphonic acid monolayers. Short-circuit currents could be raised by a factor two to four using such type of molecules. The overall efficiency of the device could be strongly increased, reaching 1 % at 0.1 Sun (AM 1.5). CBD was also used to deposit PbSe and CdSe layers at the surface of TiO2. Fluorescence spectroscopy was used to probe electron injection from CdSe quantum dots to TiO2. Generally it was observed that metal sulfides were more efficient in sensitizing TiO2/OMeTAD heterojunctions then the respective selenides.

EPFL2004

Interface engineering in solid-state dye-sensitized solar cells

Jessica Krüger

Dye-sensitised nanocrystalline solar cells are currently subject of intense research in the framework of renewable energies as a low-cost photovoltaic device. In particular dye-sensitised cells based on spiro-MeOTAD have gained attention as promising approach towards an organic solid-state solar cell. However, the efficiency in such dye-sensitised solid-state solar devices (SSD) was so far only ca. 10 % of the values reported at AM1.5 for the classical dye-sensitised solar cell with an electrolyte hole transporting medium (DSSC). The objective of the present work is to study the limitations that emerge from the exchange of the electrolyte by the solid-state system and that oppose photovoltaic photon-to-electron conversion as high as for the DSSC. Interfacial charge recombination is an important loss mechanism in dye-sensitised solar cells. This is particularly true for SSD, as the solid hole-transporting medium is less efficient in screening of internal fields which assist recombination. A variety of strategies were tested in the SSD to minimise interfacial charge recombination. The most promising approach was the blending of the hole-transporting medium with tert.-butylpyridine (tBP) and lithium ions. Optical and electrochemical techniques, such as nanosecond laser spectroscopy, impedance spectroscopy and photovoltaic characterisation measurements, were used to study the impact of the additives on the SSD. Both lithium ions as well as tBP were found to increase the open circuit potential of the SSD. At the same time tBP was found to considerably lower the current output. The interaction of the additives was studied and their concentration in the spiro-MeOTAD medium optimised. The doping of the spiro-MeOTAD film, which was intended to support the hole transport, was found to enhance interfacial recombination significantly. The morphological properties of the TiO2, in particular layer thickness, particle size and film porosity, play a more important role in the SSD than in the DSSC. Penetration of the hole conductor into the TiO2 pores and electron diffusion length are coupled to these properties. As a result the light harvesting cannot be controlled at will via the TiO2 film thickness and the active surface area for dye adsorption. An enhanced light harvesting for thin TiO2 layers offers advantages for the charge transport and the formation of the interpenetrating network. The dye uptake in presence of silver ions was found to increase the dye loading and to significantly improve the device performance of thin TiO2 layer devices. The mechanism of this simple dye modification technique was studied by a variety of spectroscopic techniques. From spectroscopic evidence it is inferred that the silver is binding to the sensitiser via the ambidentate thiocyanate, allowing the formation of ligand-bridged dye complexes. The beneficial influence of the silver ions on the photovoltaic performance was not limited to the application of the standard N3 dye nor to the spiro-MeOTAD. SSDs were furthermore studied by frequency resolved techniques. Intensity modulated photocurrent spectroscopy (IMPS) and intensity modulated photovoltage spectroscopy (IMVS) were performed over a wide range of illumination intensities. The IMPS and IMVS responses provide information about charge transport and electron-hole recombination processes respectively. For the range of light intensities investigated, the dynamic photocurrent response appears to be limited by the transport of electrons in the nanocrystalline TiO2 film rather than by the transport of holes in the spiro-MeOTAD. The diffusion length of electrons in the TiO2 was found to be 4.4 μm. This value was almost independent of the light intensity as a consequence of the fact that the electron diffusion coefficient and the rate constant for electron-hole recombination both increase in the same way with light intensity but with opposite sign. The results of this work provide for a substantial improvement of the overall photovoltaic performance compared to earlier results for this type of SSD. However, this study reveals also that high conversion efficiencies as are measured for DSSC are not likely to be reachable with the spiro-MeOTAD system due to the significantly slower charge transport in the spiro-MeOTAD compared to the electrolyte redox mediator.

EPFL2003

Novel organic dyes for enhanced red to near IR response in dye sensitised solar cells

The aim of this work was to develop new, organic dyes, capable of harvesting photons in the red to near-IR region of the spectrum. A series of squaraine and tricarbocyanine dyes were produced and characterised and their optical and redox properties studied. The results of initial photovoltaic tests, followed by optimisations of cell performance, have also been presented. These clearly demonstrate the effectiveness of these dyes in solar cells. A total of 12 new squaraine dyes were successfully synthesised, seven of which were tested in "dye-sensitised" solar cells. The efficiencies ranged from 1.2%-3.7%, for the best dye [B1]. It was concluded that enhanced performance could be achieved in the presence of chenodeoxycholic acid (CDCA) and tetrabutylpyridine (TBP). These additives both help to prevent aggregation and increase the cell potential, limiting charge collection losses and enhancing performance. Three new tricarbocyanine dyes were also synthesised, two of which were used in solar cells. Unfortunately, due to the interaction of [B12] with the electrolyte, the dye proved to be unstable, as both the absorption maxima in UV-vis and fluorescence emission wavelengths were shifted to higher energies. Thus, the red response of the dye was significantly reduced and photovoltaic performance hindered. A limited photo-response of [B14] was also seen, although this dye appeared to be very stable in the presence of the electrolyte. To deduce the possible reasons for the poor performance of these dyes, their optical and electrochemical properties were investigated. Thus, cyclic voltametry was employed to identify the redox potentials of the dyes and their charge injection and recombination dynamics were studied through nanosecond time-resolved transient laser spectroscopy. It was concluded that the dyes theoretically possess the ideal characteristics for solar cell function and that the problem of [B14] lay in the purity of the dye. [B14] proved to be very difficult to purify as the dye was unstable in solution and decomposed on the columns employed in chromatography. Fortunately the dye appeared to be stable in the presence of an electrolyte when adsorbed on TiO2. The dye gave an IPCE of 12% between 800 – 900nm, which is particularly impressive, especially if the purity of the dye is considered. A new method of purification must be found however, if photovoltaic performance is to be enhanced. Finally, the effects of a compact blocking layer on device performance were studied. It was clearly demonstrated that a compact layer was essential. This was investigated and a relationship between the structure of the dye and the necessity of the blocking layer was established.