Publication

Heat expandable biopolymers for one-step production of foam core sandwich composites

Yonghoon Yoon
2016
EPFL thesis
Abstract

The overall aim of this work has been to develop sustainable solid thermally activated foam precursors suitable for the in-line production of lightweight bio-based foam core sandwich structures with consolidated wood particle facings, using a non-inflammable, non-VOC (volatile organic compound) as a blowing agent. A preliminary study showed that expandable PLA (polylactide)/CO2 could be prepared by impregnation of PLA, a commercially available bio-based polyester, with supercritical CO2. However, the high processing temperatures, T, and pressures, P, associated with supercritical conditions resulted in premature foaming during the depressurization step, making it difficult to adapt this technique to the production of foam precursors in the particleboard process. In this thesis, PLA-based foam precursors were therefore prepared using impregnation in liquid CO2 at moderate T and P. It was subsequently shown that the resulting heat-expandable materials could be successfully implemented in a simple one-step batch process for the manufacture of foam core particleboard, an important first step towards full implementation in a continuous process at the industrial scale. The first part of the study involved determination of the optimum conditions for the impregnation of PLA with CO2, so as to prepare foam precursors that were not only stable with respect to foaming at ambient T and P but also expanded readily at elevated T. Absorption and desorption of CO2 from initially amorphous low and intermediate D-isomer content PLA was modeled using a concentration, c, dependent diffusion coefficient, D[c], such that D[c]=D[0]exp[Ac]. The empirical constants D[0] and A were obtained by modeling desorption results under various conditions. It was hence shown that CO2 uptake by PLA at about 5 MPa and 10 °C was associated with a step-like concentration gradient, consistent with the morphologies observed in PLA specimens treated with liquid CO2 for different times and then foamed. Further evidence in support of the model was obtained from observations of CO2-induced crystallization in low D-isomer content PLA. The high melting temperature, Tm, of around 170 °C of the resulting crystalline phase nevertheless hindered subsequent foam expansion at T at and around 100 °C, i.e. the range of T associated with the particleboard process, which is turn fixed by the evolution of water vapor from the wood particles used to form the facings. Crystallization could be avoided through use of fully amorphous PLA with an intermediate D-isomer content. Indeed, the significant reduction in the glass transition temperature, Tg, in the presence of high concentrations of CO2, meant that amorphous specimens saturated under the chosen impregnation conditions, i.e. containing close to 40 wt% CO2, tended to foam spontaneously at room temperature, which is inconsistent with the stability requirements of the particleboard process. However, impregnation for a limited time, followed by partial CO2 desorption at low T under conditions that could be inferred directly from the diffusion model, was shown to lead to solid foam precursors with a uniform CO2 content of around 0.1 g/g. These were not only stable at room temperature, but contained sufficient CO2 for the production of low density foams on heating. ...

About this result
This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.
Related concepts (36)
Supercritical fluid
A supercritical fluid (SCF) is any substance at a temperature and pressure above its critical point, where distinct liquid and gas phases do not exist, but below the pressure required to compress it into a solid. It can effuse through porous solids like a gas, overcoming the mass transfer limitations that slow liquid transport through such materials. SCF are much superior to gases in their ability to dissolve materials like liquids or solids.
Bioplastic
Bioplastics are plastic materials produced from renewable biomass sources, such as vegetable fats and oils, corn starch, straw, woodchips, sawdust, recycled food waste, etc. Some bioplastics are obtained by processing directly from natural biopolymers including polysaccharides (e.g., starch, cellulose, chitosan, and alginate) and proteins (e.g., soy protein, gluten, and gelatin), while others are chemically synthesised from sugar derivatives (e.g.
High-temperature superconductivity
High-temperature superconductors (abbreviated high-Tc or HTS) are defined as materials with critical temperature (the temperature below which the material behaves as a superconductor) above , the boiling point of liquid nitrogen. They are only "high-temperature" relative to previously known superconductors, which function at even colder temperatures, close to absolute zero. The "high temperatures" are still far below ambient (room temperature), and therefore require cooling.
Show more
Related publications (57)

Co-Adsorption of Alcohols and Water in JUK-8 Studied Using Quasi-Equilibrated Thermodesorption

Pattaraphon Rodlamul

JUK-8 ([Zn(oba)(pip)]n, oba2- = 4,4 '-oxybis(benzenedicarboxylate), pip = 4-pyridyl-functionalized benzene-1,3-dicarbohydrazide) is a hydrolytically stable flexible metal-organic framework. Owing to its unusual adsorptive properties, JUK-8 can be considere ...
MDPI2024

Tailoring the performance of nanocellulose-based multilayer-barrier paperboard using biodegradable-thermoplastics, pigments, and plasticizers

Tiffany Abitbol

In this work a multilayer barrier paperboard was produced in a roll-to-roll process by slot-die coating of nanocellulose (microfibrillated cellulose or carboxymethylated cellulose nanofibrils) followed by extrusion coating of biodegradable thermoplastics ( ...
SPRINGER2023

A universal signature in the melting of metallic nanoparticles

Kevin Rossi

Predicting when phase changes occur in nanoparticles is fundamental for designing the next generation of devices suitable for catalysis, biomedicine, optics, chemical sensing and electronic circuits. The estimate of the temperature at which metallic nanopa ...
ROYAL SOC CHEMISTRY2021
Show more
Related MOOCs (18)
SES Swiss-Energyscope
La transition énergique suisse / Energiewende in der Schweiz
Sorption and transport in cementitious materials
Learn how to study and improve the durability of cementitious materials.
Plasma Physics: Introduction
Learn the basics of plasma, one of the fundamental states of matter, and the different types of models used to describe it, including fluid and kinetic.
Show more