Gallium Nitride as Transparent Electron-Selective Contact in Silicon Heterojunction Solar Cells

Christophe Ballif, Mathieu Gérard Boccard, Tzu-Chin Chang Chien, Angela Nicole Fioretti, Yashi Xiao
2019
Conference paper

Abstract

Carrier-selective, passivating contacts have allowed silicon heterojunction (SHJ) cells to reach recordbreaking efficiencies particularly in all-back-contacted designs. However, two-side-contacted SHJ cell efficiency has been limited due in part to parasitic absorption losses up to 3 mA/cm2 in the aSi:H layers. More transparent materials could reduce this current loss while minimizing process complexity. Gallium nitride (GaN), with a bandgap of 3.4 eV and an advantageous band alignment with silicon, could be applied as a transparent electron-selective layer. Here, we report on SHJ solar cells utilizing PECVD GaN layers grown at 200°C as electron-selective contact. First devices exhibited open-circuit voltages of ~575 mV due to poor passivation, and low conductivity of the as-yet undoped GaN layers induced high series resistance (Rs). However, this Voc suggests the potential for electron selectivity if appropriate passivation and doping strategies are implemented.

Official source

https://infoscience.epfl.ch/record/267852?ln=en

About this result

This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.

Related concepts

Related publications

Silicon-Rich Silicon Carbide Hole-Selective Rear Contacts for Crystalline-Silicon-Based Solar Cells

Christophe Ballif, Matthieu Despeisse, Franz-Josef Haug, Quentin Thomas Jeangros, Philipp Friedrich Hermann Löper, Xavier Niquille, Gizem Nogay, Josua Andreas Stückelberger, Philippe Wyss

The use of passivating contacts compatible with typical homojunction thermal processes is one of the most promising approaches to realizing high-efficiency silicon solar cells. In this work, we investigate an alternative rear-passivating contact targeting facile implementation to industrial p-type solar cells. The contact structure consists of a chemically grown thin silicon oxide layer, which is capped with a boron-doped silicon-rich silicon carbide [SiCx(p)] layer and then annealed at 800–900 °C. Transmission electron microscopy reveals that the thin chemical oxide layer disappears upon thermal annealing up to 900 °C, leading to degraded surface passivation. We interpret this in terms of a chemical reaction between carbon atoms in the SiCx(p) layer and the adjacent chemical oxide layer. To prevent this reaction, an intrinsic silicon interlayer was introduced between the chemical oxide and the SiCx(p) layer. We show that this intrinsic silicon interlayer is beneficial for surface passivation. Optimized passivation is obtained with a 10-nm-thick intrinsic silicon interlayer, yielding an emitter saturation current density of 17 fA cm–2 on p-type wafers, which translates into an implied open-circuit voltage of 708 mV. The potential of the developed contact at the rear side is further investigated by realizing a proof-of-concept hybrid solar cell, featuring a heterojunction front-side contact made of intrinsic amorphous silicon and phosphorus-doped amorphous silicon. Even though the presented cells are limited by front-side reflection and front-side parasitic absorption, the obtained cell with a Voc of 694.7 mV, a FF of 79.1%, and an efficiency of 20.44% demonstrates the potential of the p+/p-wafer full-side-passivated rear-side scheme shown here.

Amer Chemical Soc2016

In this thesis, we present the development and characterization of novel approaches to carrier-selective passivating contacts for crystalline silicon (c-Si) solar cells. In our first approach, we benefit from a wide-bandgap material, namely mixed-phase silicon oxide (SiOx). High hydrogen dilution during the plasma-enhanced chemical vapor deposition of a SiOx layer leads to the growth of vertically oriented silicon filaments embedded in a silicon oxide matrix. The resulting mixed-phase material combines transparency and vertical conduction through the layer. We propose a layered contact structure starting with an ultra-thin chemically grown SiOx (~1.2 nm) at the c-Si wafer surface, followed by a phosphorus-doped bilayer of the mixed-phase SiOx, finishing with a nanocrystalline silicon layer that ensures contact with the metallization. With such a stack, an electron-selective passivating contact with a saturation current density J0 of 5.3 fA/cm2 is achieved on n-type wafers with hydrogenation, whereas on p-type wafers the contact reached 5.8 fA/cm2 even without hydrogenation. The contact is analyzed in detail with respect to its structure and its change upon thermal treatment. Two different growth regions are detected: one with the vertically oriented silicon inclusions and a second one in which the silicon phases have more lateral growth. Crystallization and atomic redistribution are analyzed during in-situ annealing in an electron microscope, leading to a better understanding of the change in distribution of phosphorus and oxygen as well as the nucleation sites. The influence of the annealing temperatures and dwell times as well as the initial doping concentration on the resulting in-diffused region and the passivation quality is reported. We use simulations to relate the influence of these parameters on passivation to the different recombination mechanisms. From the analyzed phosphorus doping profiles, an interesting observation is reported. The chemical oxide varies in thickness and density depending on the wafer polarity as well as the base resistivity. Proof-of-concept cells including this novel structure demonstrate the suitability for electron-selective passivating contacts at the device level with conversion efficiencies of 19.0% on planar wafers and 20.1% on textured wafers. Promisingly high short-circuit current densities (Jsc) of 35 mA/cm2 (40 mA/cm2) on planar (textured) with low parasitic absorption indicate its potential as a front contact in next-generation solar cells. Additionally, the beneficial feature of the smooth refractive index change within the layers that leads to a low reflectance over a broad wavelength range, similar to a built-in anti-reflection coating, is presented. A second approach to reach highly transparent electron-selective passivating contacts is demonstrated by the use of a plasma process based on the precursor gases phosphine (PH3), silicon tetrafluoride (SiF4), hydrogen (H2), and argon (Ar). The beneficial effect of fluorine in terms of passivation without the need for additional hydrogenation processes is shown, reaching implied open-circuit voltages of 730 mV on planar surfaces and 707 mV on textured surfaces. These layers are implemented in first proof-of-concept working devices with efficiencies of 19.5% on single-side-textured wafers and Jsc values of up to 40 mA/cm2.

EPFL2018

Silicon-Rich Silicon Carbide Hole-Selective Rear Contacts for Crystalline-Silicon-Based Solar Cells

Christophe Ballif, Matthieu Despeisse, Franz-Josef Haug, Quentin Thomas Jeangros, Philipp Friedrich Hermann Löper, Xavier Niquille, Gizem Nogay, Josua Andreas Stückelberger, Philippe Wyss

Amer Chemical Soc2016

EPFL2018