alpha-CsPbI(3)Bilayers via One-Step Deposition for Efficient and Stable All-Inorganic Perovskite Solar Cells

The emerging inorganic CsPbI(3)perovskites are promising wide-bandgap materials for application in tandem solar cells, but they tend to transit from a black alpha phase to a yellow delta phase in ambient conditions. Herein, a gradient grain-sized (GGS) CsPbI(3)bilayer is developed to stabilize the alpha phase via a single-step film deposition process. The spontaneously upward migration of (adamantan-1-yl)methanammonium (ADMA) based on the hot-casting technique causes self-assembly of the hierarchical morphology for the perovskite layers. Due to the strong steric effect of the surficial ADMA cation, a self-assembly tiny grain-sized CsPbI(3)layer is in situ formed at the surface site, which exhibits notably enhanced phase stability by its high surface energy. Meanwhile, a large grain-sized CsPbI(3)layer is obtained at the bottom site with high charge mobility and low trap density of states, which benefits from the regulated growth rates by the interaction between ADMA and perovskites. The perovskite solar cell (PSC) based on the GGS CsPbI(3)bilayer shows an efficiency of 15.5% and operates stably for 1000 h under ambient conditions. This work confirms that redistributing the surface energy of perovskite films is a facile strategy to stabilize metastable PSCs without the cost of efficiency loss.

Stability in 3D and 2D/3D hybrid perovskite solar cells studied by EFISHG and IS techniques under light and heat soaking

Zubair Ahmad, Kyung Taek Cho, Mohammad Khaja Nazeeruddin, Sanghyun Paek

We investigate the effect of temperature and light soaking on the stability and charge carrier behavior in triple cation 3-Dimensional (3D) and 2-Dimensional (2D)/3-Dimensional perovskite solar cells (PSCs) using electric field induced second harmonic generation (EFISHG) and impedance spectroscopy (IS) techniques. To prepare the 2D/3D perovskite structures, a layer-by-layer deposition method was employed. Spiro-OMeTAD based hole transport layer was deposited on the top of the perovskite layer using a spin coaling procedure. The average power conversion efficiency (PCE) of the fresh fabricated cells was similar to 18%. The electric fields in the PSCs were selectively probed by the EFISHG measurements, using the fundamental laser beam wavelength of 960 nm. The results show that the EFISHG technique could be potentially used to identify the degradation mechanism in the PSCs. Also, the IS technique was performed to investigate the electrical parameters affected under light and heat soaking environment The 2D/3D hybrid PSCs show relatively good stability and better efficiency as compared to 3D PSCs.

ELSEVIER SCIENCE BV2019

Strategies to Optimizing Dye-Sensitized Solar Cells

Sophie Wenger

Dye-sensitized solar cells (DSCs) constitute a novel class of hybrid organic-inorganic solar cells. At the heart of the device is a mesoporous film of titanium dioxide (TiO2) nanoparticles, which are coated with a monolayer of dye sensitive to the visible region of the solar spectrum. The role of the dye is similar to the role of chlorophyll in plants; it harvests solar light and transfers the energy via electron transfer to a suitable material (here TiO2) to produce electricity — as opposed to chemical energy in plants. DSCs are fabricated of abundant and cheap materials using inexpensive processes (e.g. screen-printing) and are likely to be a significant contributor to the future commercial photovoltaic technology portfolio. The work conducted during this thesis aimed at optimizing the DSC using three different strategies: The use of versatile organic sensitizers for stable and efficient DSCs, the study of tandem device architectures in combination with other solar cells to harvest a larger fraction of the solar spectrum, and the development of a validated optoelectric model of the DSC. Organic donor-π-acceptor dyes are an interesting alternative to the standard metal-organic complexes used in DSCs. Efficient photovoltaic conversion and stable performance could be demonstrated with three classes of donor systems, namely diphenylamine, difluorenylaminophenyl, and π-extended tetrathiafulvalene. The highest conversion efficiencies were obtained with a difluorenylaminophenyl donor system (η = 8.3 % with a volatile electrolyte and η = 7.6 % with a solvent-free ionic liquid, which was a new record for organic dyes at the time of publication). Surprisingly, efficient regeneration of the oxidized dye by the I-/I3- redox mediator was found with the π-extended tetrathiafulvalene system, even though the thermodynamic driving force was as low as 150 mV. So far driving forces of 300-500 mV had been regarded as necessary for efficient regeneration of the dye cation. Also, important structure-property relationships pertaining to the recombination of electrons with the electrolyte and to the stability of the device could be identified (i.e. effect of linear vs. branched structure, linker length, and moieties used). The power conversion efficiency of solar cells can be extended beyond the limit for a single cell (∼ 30 %) by using multiple cells with different optical gaps in a tandem device. DSCs and chalcopyrite Cu(In,Ga)Se2 (CIGS) solar cells have complementary optical gaps and are thus suitable systems for integration in a tandem device. It was shown that a monolithic DSC/CIGS tandem device has the potential for increased efficiency over a mechanically stacked device due to increased light transmission to the bottom cell, and a monolithic DSC/CIGS device with an initial efficiency of η = 12.2 % was demonstrated. The degradation of the devices — induced by the corrosion of the CIGS cell in contact with the I-/I3- redox mediator — could be retarded with a protective thin conformal ZnO/TiO2 oxide layer coated on the CIGS cell by atomic layer deposition. Finally, an experimentally validated optical and electrical model of the DSC has been developed to assist the optimization process, which is predominantly conducted by empirical means in the DSC research community. The optical model allows to accurately calculate the internal quantum efficiency of devices, i.e. the ratio of extracted electrons to absorbed photons by the dye, a crucial and so far difficult to determine characteristic. Intrinsic parameters — like injection efficiency, electron diffusion length, or distribution of trap states in the TiO2 — can be extracted from experimental steady-state and time-dependent data with the electric model. The model allows to make a comprehensive and quantitative loss analysis of the different optical and electric loss channels in the DSC. The model has been implemented with a graphical user interface for straightforward usage. All three optimization strategies — organic dyes, tandem architecture, and device modeling — developed during this thesis make a valuable contribution to the development and commercialization of inexpensive and high efficiency DSCs. They enable a comprehensive view of the system and pave the way for a systematic analysis and reduction of losses, which has been the ultimate route to success for several established photovoltaic technologies.

EPFL2010

A Material Approach to Dye-Sensitized Solar Cells

Philippe Pierre Labouchère

With growing concerns on future energy supplies, solar energy appears as an energy source whose potential remains to be tapped at a large scale. In the last two decades, dye-sensitized solar cells (DSCs) have been considered as a competitive means to convert solar energy into electricity thanks to their low manufacturing and environmental costs, simple fabrication and high efficiency. Indeed, record efficiencies as high as 13% have been obtained for liquid DSCs and recently, solid-state DSCs using solid hole transport materials as well as perovskite materials as sensitizers have showed efficiencies above 17%. From a physical point of view, charge carrier generation in a DSC takes place in a photoactive light harvester chemisorbed on a mesoscopic semiconductor oxide. Due to the excellent electronic overlap, the exciton separation occurs by the injection of the excited electrons and holes from the dye into the conduction band of the semiconductor and redox electrolyte, respectively. A high surface area mesoscopic photoanode is necessary to ensure a high-density bulk heterojunction and efficient light harvesting in the visible part of the solar spectrum due to effective dye loading. This implies that the DSC has a large, heterogeneous interface through which photogenerated electrons may be intercepted as a result of the slow electron transport. The latter is governed by an ambipolar diffusion mechanism controlled by trap-limited hopping through a long path to the transparent conductive electrode. It is however hindered by the low electron mobility in anatase TiO2 nanoparticles and the multiple grain boundaries in the mesoporous film. The work conducted during this thesis aimed at developing new architectures for the electrodes of DSCs using notably atomic layer deposition (ALD) and inverse opal host-guest structures with different semiconducting metal oxides. First, using a self-assembled polymeric template and ALD, we fabricated a porous ZnO inverse opal backbone. Advantages are numerous: a high electronic mobility of ZnO, a precise control of the metal oxide deposition using ALD and in situ growth of ZnO nanowires at low temperatures. Besides increasing the surface area available for photoactive dye molecules, single-crystal nanowires offer a defect-free path for photoinjected electrons. However, because of the relative instability of ZnO in acidic environments, a TiO2 overlayer was deposited by ALD. This proved to increase the recombination resistance of photogenerated electrons and increased their lifetime in the porous film. This host-guest approach was further transposed to three related fields in photo-electrochemistry using different ALD precursors. For water splitting, a niobium-doped tin oxide inverse opal backbone was constructed, which served as a host for hematite deposited by atmospheric pressure chemical vapour deposition or ALD. In the field of plasmonics, a TiO2 inverse opal host was made to act as a scaffold for silver nanoparticles. For solid-state DSCs, we strived to achieve an ultra-thin ZnO inverse opal, which acted as a host for perovskite crystals. Finally, we studied the effect of very thin TiO2 and ZnO overlayers deposited by ALD on top of mesoporous ZnO and TiO2, respectively. We were able to accurately monitor the thickness of overlayers and study the effects on photovoltaic parameters such as transport and recombination rates of photogenerated electrons, photocurrent, photovoltage, fill factor and efficiency.