Optoelectronic Properties of Layered Perovskite Solar Cells

Herein, the optoelectronic properties of interface-engineered perovskite 2D|3D-heterojunction structure solar cells are reported. The reciprocity theorem is applied to determine the maximum open-circuit voltage (V-oc) the device can deliver under solar illumination. A V-oc of 1.295 V is found, analyzing the measured external quantum efficiency and assuming only radiative recombination. For comparison, the experimental open-circuit voltage found for the studied 2D|3D heterojunctions is 1.15 V. The contribution of nonradiative recombination is explored by measuring the electroluminescence quantum yield. A quantum yield of 0.4% is found at current densities equivalent to 1 sun illumination. This translates into a V-oc loss of approximate to 140 mV, which is in very good agreement with the experimental findings. In addition, the fundamental correlation between luminescence intensity and the chemical potential predicted by the generalized Planck law is confirmed for the photoluminescence measured at different light intensities when the device is operated under open-circuit conditions and for the electroluminescence when operated under a forward bias. The investigations in this study suggest that further efficiency improvements can be achieved by reducing the nonradiative recombination in the studied solar cell. At the same time, a high-performance near IR light emitting diode can be realized.

Dimensionally Engineered Perovskite Heterostructure for Photovoltaic and Optoelectronic Applications

Kyung Taek Cho, Yonghui Lee, Mohammad Khaja Nazeeruddin, Sanghyun Paek

Although 2D|3D has shown potential for application in multifunctional devices, the principle of operation for multifunction devices (SOLAR Cell-LED: SOLED) has not yet been revealed. However, most studies have reported that the devices have only one auspicious characteristic. Here in this study the SOLED devices are monitored and investigated in a 2D|3D heterostructure with a multidimensional perovskite. It is fond that a 2D|3D heterostructure with a multidimensional perovskite interface induces carrier transmission from the interface, increasing the density of electrons and holes, and increasing their recombination. An interface-engineered perovskite 2D|3D-heterojunction structure is employed to realize the multifunctional photonic device in on-chip, exhibiting overall power conversion efficiencies of photovoltaics up to 21.02% under AM1.5, and external quantum efficiency of the light-emitting diode up to 5.13%. This novel phenomenon is attributed to carrier transfer resulting in a high carrier density and enhanced carrier recombination at the 2D|3D interface.

2019

Strategies to Optimizing Dye-Sensitized Solar Cells

Sophie Wenger

Dye-sensitized solar cells (DSCs) constitute a novel class of hybrid organic-inorganic solar cells. At the heart of the device is a mesoporous film of titanium dioxide (TiO2) nanoparticles, which are coated with a monolayer of dye sensitive to the visible region of the solar spectrum. The role of the dye is similar to the role of chlorophyll in plants; it harvests solar light and transfers the energy via electron transfer to a suitable material (here TiO2) to produce electricity — as opposed to chemical energy in plants. DSCs are fabricated of abundant and cheap materials using inexpensive processes (e.g. screen-printing) and are likely to be a significant contributor to the future commercial photovoltaic technology portfolio. The work conducted during this thesis aimed at optimizing the DSC using three different strategies: The use of versatile organic sensitizers for stable and efficient DSCs, the study of tandem device architectures in combination with other solar cells to harvest a larger fraction of the solar spectrum, and the development of a validated optoelectric model of the DSC. Organic donor-π-acceptor dyes are an interesting alternative to the standard metal-organic complexes used in DSCs. Efficient photovoltaic conversion and stable performance could be demonstrated with three classes of donor systems, namely diphenylamine, difluorenylaminophenyl, and π-extended tetrathiafulvalene. The highest conversion efficiencies were obtained with a difluorenylaminophenyl donor system (η = 8.3 % with a volatile electrolyte and η = 7.6 % with a solvent-free ionic liquid, which was a new record for organic dyes at the time of publication). Surprisingly, efficient regeneration of the oxidized dye by the I-/I3- redox mediator was found with the π-extended tetrathiafulvalene system, even though the thermodynamic driving force was as low as 150 mV. So far driving forces of 300-500 mV had been regarded as necessary for efficient regeneration of the dye cation. Also, important structure-property relationships pertaining to the recombination of electrons with the electrolyte and to the stability of the device could be identified (i.e. effect of linear vs. branched structure, linker length, and moieties used). The power conversion efficiency of solar cells can be extended beyond the limit for a single cell (∼ 30 %) by using multiple cells with different optical gaps in a tandem device. DSCs and chalcopyrite Cu(In,Ga)Se2 (CIGS) solar cells have complementary optical gaps and are thus suitable systems for integration in a tandem device. It was shown that a monolithic DSC/CIGS tandem device has the potential for increased efficiency over a mechanically stacked device due to increased light transmission to the bottom cell, and a monolithic DSC/CIGS device with an initial efficiency of η = 12.2 % was demonstrated. The degradation of the devices — induced by the corrosion of the CIGS cell in contact with the I-/I3- redox mediator — could be retarded with a protective thin conformal ZnO/TiO2 oxide layer coated on the CIGS cell by atomic layer deposition. Finally, an experimentally validated optical and electrical model of the DSC has been developed to assist the optimization process, which is predominantly conducted by empirical means in the DSC research community. The optical model allows to accurately calculate the internal quantum efficiency of devices, i.e. the ratio of extracted electrons to absorbed photons by the dye, a crucial and so far difficult to determine characteristic. Intrinsic parameters — like injection efficiency, electron diffusion length, or distribution of trap states in the TiO2 — can be extracted from experimental steady-state and time-dependent data with the electric model. The model allows to make a comprehensive and quantitative loss analysis of the different optical and electric loss channels in the DSC. The model has been implemented with a graphical user interface for straightforward usage. All three optimization strategies — organic dyes, tandem architecture, and device modeling — developed during this thesis make a valuable contribution to the development and commercialization of inexpensive and high efficiency DSCs. They enable a comprehensive view of the system and pave the way for a systematic analysis and reduction of losses, which has been the ultimate route to success for several established photovoltaic technologies.

EPFL2010

Approches numériques du transport de charges dans les semiconducteurs organiques

Hocine Houili

Using plastics or dyes like molecular semiconductors to make optoelectronic devices at low cost is a project in industry that is of great interest to the "Information Community" of this beginning of the 21st century. Some applications of this technology have already been realized including flexible flat-panel displays made with organic light-emitting diodes, organic transistors for active matrices, organic solar cells and sensors. In all these applications it is essential to deduce and understand the laws that determine the charge transport and the light emission in these materials. The goal of this thesis is to contribute to the theoretical models that describe these transport processes. In order to predict the behaviour of charge carriers in a given device, one can choose two methods. One can either numerically solve the master equations that describe the general behaviour of charges and currents in each part of the device, or one can simulate the detailed behaviour of each charge in the device by fixing the conditions of its movement using a procedure known as "Monte Carlo". In this thesis I addressed the two approaches. I have been interested successively in the prediction of the electric properties of multilayer light-emitting devices, considered as a whole. Then I was able to understand in detail the processes accruing at the organic-organic interfaces by using the Monte Carlo method. My last project involved the study of the channel of an organic transistor. In each one of these cases I took account of the characteristic features of small molecule organic materials in order to develop models for charge transport for the study and optimization of two important types of organic devices : organic light-emitting diodes and field-effect transistors. Amorphous organic semiconductors are mainly used for the fabrication of organic diodes. They are characterized by an energetically disordered density of states that is assumed to be Gaussian. The transport of charges in these materials occurs via hopping from one molecule to another in this density of states. The correlations between the energies of the molecular sites have important effects on transport ; the dependence of mobility on the applied electric field in particular. If the energetic disorder is due to the random orientations of the permanent dipoles of the molecules, then the correlations between the orientations of these dipoles can profoundly change the spatial configuration of the energetic disorder and consequently the charge transport. Due to the fact that organic diodes often comprise of multiple organic layers, understanding device behaviour at the organic-organic interfaces is of critical importance. Electrons and holes accumulate close to these interfaces and they are therefore more likely to recombine and emit light. The Coulomb interactions between the charge carriers and the energy disorder are at the origin of complex processes taking place at these accumulation regions. I studied these processes through a 3D multi-particle Monte Carlo simulation. The short-range Coulomb repulsion forbids the double-occupancy of the sites and shifts the energy level for injection of carriers across the interface upward, thus increasing the electric current of the diode. The long-range Coulomb interactions increase the electric field and the current at the interface although this increase is less important than suggested by 1D models. Effects related to the hopping process such as the effect of the exact form of the hopping law and backward or return hop at the interface are clearly discussed. The Monte Carlo simulations are cross-compared with an analytical model for hopping transport across the interface. This comparison made it possible to understand other aspects of the physical processes at organic-organic interface and supports the Monte Carlo simulations. The study of the electron-hole recombination showed a decrease of the cross-section with an increase of the applied electric field, but this decrease is less than what can be expected by the classical Langevin theory. In spite of their efficiency, Monte Carlo simulations are not attractive when modelling complex multi-layer diodes. The 1D models are better suited in this case. A 1D model called MOLED, which was developed at Laboratoire d'Optoélectronique des Matériaux Moléculaires (LOMM) for the simulation of the organic diodes, is used and described in detail in this thesis. We used MOLED to explore the effect of the energy correlations on the electric field dependence of the mobility. In fact we simulated the time-of-flight experiment, a common method used to determine of the carrier mobility. The crystalline organic semiconductors achieve mobility performances close or even better than amorphous silicon. Their use for the fabrication of field-effect transistors is thus a good choice. The models for charge transport in crystalline organic materials differ much from their counterparts for amorphous organic materials. Indeed band models are more appropriate to describe charge transport in crystalline organic materials. However it is very important to take into account the effects of electronic polarization in these models. I developed a method of calculation of these effects of polarization in the bulk of the organic semiconductor and I extended it to the case of the interface with a dielectric insulator, a situation encountered in the channel of the organic transistor. These calculations showed that when the polarity of the dielectric increases the inter-molecular transfer integral decreases. This is confirmed by experimental measurements showing increasingly low values of mobility when the permittivity of the insulator increases.