Publications associées à T-beam

FLO:RE – A new floor system made of reused reinforced concrete and steel elements

Corentin Jean Dominique Fivet, Numa Joy Bertola, Maléna Bastien Masse, Célia Marine Küpfer

Carefully extracting reinforced concrete (RC) elements from soon-to-be demolished structures and reusing them as load-bearing components is an emerging circular low-carbon alternative to building new structures. As floor construction typically accounts for ...

IABSE2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Digital-Image-Correlation for Simulating Cyclic Local Buckling in Steel Beams

Dimitrios Lignos, Albano António De Abreu E Presa De Castro E Sousa, Selimcan Ozden

Nonlinear continuum finite element (CFE) analyses rely on accurate multiaxial constitutive law formulations along with reliable imperfection patterns for simulating nonlinear geometric instabilities in steel members under mechanical loading. Validations of ...

Wiley2023

Geometric tolerances of welded connections with inelastic panel zones

Dimitrios Lignos, Andronikos Skiadopoulos, Ce Wen

Prequalified beam-to-column connections in steel moment resisting frames usually concentrate inelastic deformations in the steel beam ends. As such, nonlinear geo-metric instabilities (i.e., local buckling) may occur in these regions at modest lateral drif ...

Ernst & Sohn2023

Full Scale Experiments of a Composite Steel Moment Resisting Frame: Behavioral Insights and Implications on Seismic Design

Dimitrios Lignos, Hammad El Jisr

This paper discusses the cyclic performance of a heavily instrumented 2-bay full-scale composite-steel moment resisting frame (CMRF) sub-system from the onset of structural damage up until incipient collapse. The CMRF featured stiffened end plate bolted co ...

EEME2023

The new Chapter 9 of Eurocode 8 Part 3 for Seismic Assessment of Existing Steel Structures

Dimitrios Lignos

The seismic assessment of existing steel structures necessitates the development of practice- oriented engineering models for use in nonlinear static and dynamic analysis procedures. These models should encompass the full range of the anticipated nonlinear ...

2023

Exploring the potential of the critical shear crack theory for reinforced and post-tensioned glass beams: Initial analysis and experiments

Alain Nussbaumer, Pieter Christian Louter, Jagoda Cupac

In the evolution of structural glass beam elements, the requirements for post-fracture load bearing capacity and safe failure behaviour have led to the development of reinforced and post-tensioned beams. Maximum bending capacity in the post-fracture state ...

2023

Full-Scale Experiments of Cyclically Loaded Welded Moment Connections with Highly Dissipative Panel Zones and Simplified Weld Details

Dimitrios Lignos, Andronikos Skiadopoulos

This paper presents the experimental results of two welded unreinforced flange-welded web (WUF-W) beam-to-column connections that defy the current design paradigm of prequalified welded connections. The proposed WUF-W connections feature customized beveled ...

2023

Towards instability-free welded moment connections

Dimitrios Lignos, Andronikos Skiadopoulos

In capacity-designed steel moment resisting frames (MRFs), inelastic deformations are mostly concentrated in the steel beams and the column fixed ends of the first story, while the participation of the panel zones in energy dissipation is limited. In such ...

2023

Full-scale testing of European steel beams with reduced beam section under reversed cyclic loading

Dimitrios Lignos, Hiroyuki Inamasu

Steel beams with reduced beam section (RBS) are often used as part of prequalified connections in seismic regions. However, RBS connections are not as common in Europe. Reasons relate to easiness in fabrication, which requires on-site welding, and the seis ...

Springer Nature2022