Quad Flat Package

A quad flat package (QFP) is a surface-mounted integrated circuit package with "gull wing" leads extending from each of the four sides. Socketing such packages is rare and through-hole mounting is not possible. Versions ranging from 32 to 304 pins with a pitch ranging from 0.4 to 1.0 mm are common. Other special variants include low-profile QFP (LQFP) and thin QFP (TQFP). The QFP component package type became common in Europe and United States during the early nineties, even though it has been used in Japanese consumer electronics since the seventies. It is often mixed with hole mounted, and sometimes socketed, components on the same printed circuit board (PCB). A package related to QFP is plastic leaded chip carrier (PLCC) which is similar but has pins with larger pitch, 1.27 mm (or 1/20 inch), curved up underneath a thicker body to simplify socketing (soldering is also possible). It is commonly used for NOR flash memories and other programmable components. The quad flat-pack has connections only around the periphery of the package. To increase the number of pins, the spacing was decreased from 50 mil (as found on small outline packages) to 20 and later 12 (1.27 mm, 0.51 mm and 0.30 mm respectively). However, this close lead spacing made solder bridges more likely and put higher demands on the soldering process and alignment of parts during assembly. The later pin grid array (PGA) and ball grid array (BGA) packages, by allowing connections to be made over the area of the package and not just around the edges, allowed for higher pin counts with similar package sizes, and reduced the problems with close lead spacing. Cyrix cx9210 gfdl (cropped).jpg|144-pin low profile quad flat package (LQFP) PIC18F8720.jpg|80-pin thin quad flat package (TQFP) – [[PIC microcontroller]] Sega 304-pin QFP.jpg|304-pin plastic quad flat package (QFP) with exposed [[thermally conductive pad|thermal pad]] (TP) Cyrix Cx486SLCe-V25MP DF7339E top.jpg|100-pin bumpered quad flat package (BQFP) – [[Cyrix Cx486SLC]] CRQFP80 UV ST62E40.

À propos de ce résultat

Cette page est générée automatiquement et peut contenir des informations qui ne sont pas correctes, complètes, à jour ou pertinentes par rapport à votre recherche. Il en va de même pour toutes les autres pages de ce site. Veillez à vérifier les informations auprès des sources officielles de l'EPFL.

Publications associées (26)

Personnes associées (4)

Unités associées (8)

Concepts associés (1)

Cours associés (1)

Séances de cours associées (4)

Explore les technologies d'emballage MEMS avancées, y compris l'intégration 3D, l'emballage hermétique et les processus d'emballage au niveau des plaquettes.

Explore les techniques d'emballage MEMS avancées, y compris la technologie flip-chip et le collage au niveau des plaquettes pour le contrôle du stress et l'étanchéité hermétique.

Couvre l'emballage des systèmes intelligents, des systèmes de soudure, des principaux types d'interconnexion de puces et des tendances d'emballage.

Afficher plus

REMOTE: Re-thinking Task Mapping on Wireless 2.5D Systems-on-Package for Hotspot Removal

David Atienza Alonso, Marina Zapater Sancho, Giovanni Ansaloni, Darong Huang, Rafael Medina Morillas

2.5D Systems-on-Package (SoPs) are composed by several chiplets placed on an interposer. They are becoming increasingly popular as they enable easy integration of electronic components in the same package and high fabrication yields. Nevertheless, they int ...

2023

First developments towards producing inductive magnetic sensors using state-of-the-art photolithography techniques

Duccio Testa, Ambrine Douhane, Marcus Cemes

Inductive magnetic sensors are needed for tokamak operation to provide the low-frequency (LF) measurements leading to the equilibrium reconstruction and to monitor the higher frequency (HF) instabilities; the HF magnetic sensors are often also used as a ba ...

2023

Integration of hybrid material systems in conformable neural interfaces

Florian Dylan Fallegger

Neural interfaces are devices that are implanted into the body and interface electrically with the central (CNS) or peripheral nervous system. They are inserted surgically for short periods of time or chronically to diagnose or treat several neural disease ...

EPFL2020

Explore les technologies d'emballage MEMS avancées, y compris l'intégration 3D, l'emballage hermétique et les processus d'emballage au niveau des plaquettes.

Explore les techniques d'emballage MEMS avancées, y compris la technologie flip-chip et le collage au niveau des plaquettes pour le contrôle du stress et l'étanchéité hermétique.

Couvre l'emballage des systèmes intelligents, des systèmes de soudure, des principaux types d'interconnexion de puces et des tendances d'emballage.

Afficher plus

Une matrice de broches, ou PGA (sigle du nom en anglais pin grid array), est un type d'interconnexion entre un composant monté en surface (CMS) et un circuit imprimé (PCB). C'est un connecteur carré en plastique (ou autrefois en céramique) présent sur les cartes mères et se présentant généralement sous la forme d'une grille dotée de nombreuses perforations disposées en carré ou en quinconce servant à accueillir les pattes d'un processeur. Le mot « matrice » est utilisé dans le sens mathématique, c'est-à-dire comme tableau ou grille.

In depth analysis of the operation principles and technology of advanced micro- and nanosystems. Familiarisation to their implementation into products and their applications.