Publications de Miguel Fernández Ruiz

Verification of shear failures of cantilever bridge deck slabs subjected to concentrated loads

Shear design and verification of bridge deck slabs subjected to concentrated loads (as those of wheels from traffic) is a topic subjected to scientific and engineering debate, where several questions remain open. Several design procedures have been propose ...

Elsevier Sci Ltd2024

Stress Fields and Strut-and-Tie Models as a Basic Tool for Design and Verification in Second Generation of Eurocode 2

Aurelio Muttoni, Miguel Fernández Ruiz

Within the frame of the revision of the Eurocode 2 for concrete structures, the section devoted to strut-and-tie design has been up-dated to enhance its applicability, its consistency with other sections and its ease-of-use. As a result, a number of change ...

ASOC ESPANOLA INGENIERIA ESTRUCTURAL-ACHE2023

A Discussion on the Reliability of prEN1992-1-1:2021 Shear Strength Provisions for Fibre Reinforced Concrete Members Without Shear Reinforcement

Miguel Fernández Ruiz

The Eurocode 2 for the design of concrete structures (EN1992-1-1:2004) is undergoing a revision that will lead to the publication of the second generation of this code to be used across all CEN member countries. Therefore, the impact of the code will reach ...

SPRINGER INTERNATIONAL PUBLISHING AG2023

A Mechanical Approach for the Punching Shear Provisions in the Second Generation of Eurocode 2

Aurelio Muttoni, Miguel Fernández Ruiz, João Tiago Ramos Bernardo de Santa Rita Simões, Duarte Miguel Viúla Faria

The revision of a code is a long-term project that shall fulfil several aims, comprising the enhancement of the ease-of-use and incorporating updated state-of-the-art. With respect to the revision of Eurocode 2 concerning the punching shear provisions, thi ...

ASOC ESPANOLA INGENIERIA ESTRUCTURAL-ACHE2023

Considerations on the partial safety factor format for reinforced concrete structures accounting for multiple failure modes

Aurelio Muttoni, Miguel Fernández Ruiz, Qianhui Yu

The increasing usage of nonlinear analyses for the design of reinforced concrete structures and the necessity of codes of practice to provide a consistent safety format for them is one of the challenges that new generations of codes of practice are facing. ...

ELSEVIER SCI LTD2022

Measurement of the inclusive and differential t(t)over-bar gamma cross sections in the dilepton channel and effective field theory interpretation in proton-proton collisions at root s=13 TeV

Matthias Finger, Varun Sharma, Olivier Martin, Ian Smith, Jean-François Carlin, Arvind Shah, Rakesh Chawla, Thomas Mountford, Chao Wang, João Miguel das Neves Duarte

The production cross section of a top quark pair in association with a photon is measured in proton-proton collisions in the decay channel with two oppositely charged leptons (e(+/-)mu(-/+), e(+)e(-), or mu(+)mu(-)). The measurement is performed using 138 ...

Springer Nature2022

Characterization of shear deformations in reinforced concrete members without shear reinforcement

Aurelio Muttoni, Miguel Fernández Ruiz, Raffaele Cantone, Andri Setiawan

The load-carrying capacity of many reinforced concrete structures is governed by shear failures, occurring before reaching the flexural capacity of the member. For redundant systems, such as slabs subjected to concentrated loads, local shear failures (typi ...

2022

Influence of sustained loading on resistance and deformation capacity of reinforced concrete members in compression

Aurelio Muttoni, Xhemsi Malja, Miguel Fernández Ruiz

As acknowledged explicitly or implicitly in most of current design codes, a high level of sustained loading has a detrimental effect on the concrete compressive strength. However, its beneficial effect in terms of deformation capacity is neglected in most ...

ERNST & SOHN2022

Design of slender and squat reinforced concrete members with shear reinforcement

Aurelio Muttoni, Miguel Fernández Ruiz, Marko Pejatovic

As proposed in several design standards for structural concrete, including Eurocode 2 (EN:1992-1-1:2004) and fib's Model Code 2010, the shear design of slender members with shear reinforcement can be performed by means of consistent models based on suitabl ...

ERNST & SOHN2022

Anchorage of shear reinforcement in beams and slabs

Aurelio Muttoni, Miguel Fernández Ruiz, Qianhui Yu, Frédéric Monney

Anchorage of shear reinforcement, such as links or stirrups, can be performed by providing hooks, bends or heads at their ends, by welding transverse reinforcement or by closing open stirrups with pins. Hooks and bends, also used to enhance the anchorage o ...

2022