New microwave sensing system for blade tip clearance measurement in gas turbines

Marc Hafner, Anja Skrivervik Favre, Maddalena Violetti
Ieee, 2012
Article de conférence

Résumé

Real-time clearance control in turbine engines allows improving their efficiency and safety, by enabling prognostics and optimized condition-based maintenance in the turbine hot section. This paper presents a novel 24 GHz microwave sensing system for real-time blade tip clearance monitoring suitable for small-size turbines (aero-engines and aero-derivatives). The system principle of operation is similar to the short range radar technique and employs high temperature resistant circular waveguide resonator probes mounted into the shell of the turbine. Probes concept was proven through simulation and prototypes where built and tested, showing agreement of results. The system was validated in laboratory, where the harsh turbine environment was reproduced on dedicated test rigs. Finally, the system was tested on a real engine, showing its suitability for real-time blade tip measurement.

Official source

https://infoscience.epfl.ch/record/182546?ln=fr

À propos de ce résultat

Cette page est générée automatiquement et peut contenir des informations qui ne sont pas correctes, complètes, à jour ou pertinentes par rapport à votre recherche. Il en va de même pour toutes les autres pages de ce site. Veillez à vérifier les informations auprès des sources officielles de l'EPFL.

Concepts associés

Chargement

Publications associées

Chargement

Publications associées (4)

New Microwave Sensing System for Blade Tip Clearance Measurement in Gas Turbines

Michaël Hafner, Anja Skrivervik Favre, Maddalena Violetti

Ieee2012

Chargement

Prototype of a thermally driven heat pump based on integrated organic Rankine cycles (ORC)

Jonathan Demierre, Daniel Favrat, Samuel Henchoz

The concept studied in this work is a low power ORC-ORC system (about 20 kW heat at the condenser) which is composed of an ORC engine cycle driving a reversed ORC heat pump cycle, both using the same fluid. The radial compressor and turbine are directly coupled on the same shaft rotating on refrigerant gas bearings. This gives the system the advantage of being oil-free, fully hermetic and with low maintenance costs. The paper presents the development of an ORC-ORC prototype, with HFC-134a as working fluid. The main critical parts of the system are the compressor-turbine unit, the supercritical evaporator and the pump. The selected type of heat exchanger for the supercritical evaporation is the double tube coil (DTC). A first experimental setup has been built to test the pump and the supercritical evaporator. A comparison has been done between the results obtained with an in-house supercritical evaporator simulation tool and the measurements made on the DTC. The design steps of the compressor-turbine are briefly presented. The compressor-turbine unit has been balanced and tested, with air, at speeds up to 140'000 rpm.

2010

Chargement

The importance of renewable energy sources for the electrical power supply has grown rapidly in the past decades. Their often unpredictable nature however poses a threat to the stability of the existing electric grid. Hydroelectric powerplants play an important role in regulating the integration of renewable energy sources into the network by supplying on-demand load balancing as well as primary and secondary power network control. Therefore, the operating ranges of hydraulic machines has to be continuously extended, which potentially produces undesirable flow phenomena involving cavitation. An example is the formation of a gaseous volume in the swirling flow leaving a Francis turbine runner at off-design operating conditions. At high load, this so called vortex rope is shaped axisymmetrically and may enter a self-excited oscillation, measurable through significant fluctuations of the pressure throughout the system and the mechanical torque transferred to the generator. The main objective of the present work is the identification of the physical mechanisms governing this self-sustained, unstable behavior by measurement. Furthermore, the key parameters of numerical approaches using one-dimensional hydroacoustic flowmodels or CFD require experimental validation. For this purpose, the measurements provide a comprehensive data base of various flow and system parameters at varying operating conditions. Two test cases are studied, a small scale hydraulic circuit with a micro-turbine as well as a reduced scale physical model of an existing Francis turbine. On the first test case, the study of the flow rate fluctuations up- and downstream of the oscillating vortex rope in the draft tube, together with the volume of the cavity, revealed the destabilizing effect of the flow swirl in the draft tube inlet. The second test case accurately simulates the behavior of an actual hydraulic power plant. Investigations range from a local study of the flow field in the draft tube cone bymeans of LDV, PIV, high speed visualization and wall pressure measurements to a global analysis, considering the response of the hydraulic and mechanical system to the excitation by the vortex rope oscillation. Among the main observations is a periodical variation of the flow swirl in the draft tube, synchronized with the pressure oscillations. This is likely to be caused by a cyclically appearing volume of cavitation on the runner blades, modifying the relative flow angle at the outlet. The interaction of the blade cavitation and the vortex rope oscillation via the flow swirl is found to play a crucial role in the occurrence of self-excited pressure oscillations in Francis turbines.

EPFL2014

Chargement

Afficher plus

EPFL2014