Fabrication des dispositifs à semi-conducteursthumb|upright=1.5|Évolution de la finesse de gravure des processeurs entre 1970 et 2017 La fabrication des dispositifs à semi-conducteur englobe les différentes opérations permettant l'élaboration de composants électroniques basés sur des matériaux semi-conducteurs. Entrent dans cette catégorie de composants à semi-conducteur, les composants discrets qui n'ont qu'une seule fonction comme les diodes et les transistors, et les circuits intégrés plus complexes, intégrant plusieurs composants, jusqu'à des milliards, dans le même boîtier.
Transistor countThe transistor count is the number of transistors in an electronic device (typically on a single substrate or "chip"). It is the most common measure of integrated circuit complexity (although the majority of transistors in modern microprocessors are contained in the cache memories, which consist mostly of the same memory cell circuits replicated many times). The rate at which MOS transistor counts have increased generally follows Moore's law, which observed that the transistor count doubles approximately every two years.
Circuit intégré à signaux mixtesA mixed-signal integrated circuit is any integrated circuit that has both analog circuits and digital circuits on a single semiconductor die. Their usage has grown dramatically with the increased use of cell phones, telecommunications, portable electronics, and automobiles with electronics and digital sensors. Integrated circuits (ICs) are generally classified as digital (e.g. a microprocessor) or analog (e.g. an operational amplifier). Mixed-signal ICs contain both digital and analog circuitry on the same chip, and sometimes embedded software.
Atomic layer depositionL’atomic layer deposition (ALD) est un procédé de dépôt de couches minces atomiques. Le principe consiste à exposer une surface successivement à différents précurseurs chimiques afin d'obtenir des couches ultra-minces. Il est utilisé dans l'industrie des semi-conducteurs. L'énorme avantage de l'ALD est de pouvoir faire une monocouche sur une surface présentant un très fort rapport d'aspect (des creux et des bosses). Notamment car la réaction de CVD se déroule directement à la surface, sur une monocouche de gaz précurseurs adsorbés.
Integrated circuit layout design protectionLayout designs (topographies) of integrated circuits are a field in the protection of intellectual property. In United States intellectual property law, a "mask work" is a two or three-dimensional layout or topography of an integrated circuit (IC or "chip"), i.e. the arrangement on a chip of semiconductor devices such as transistors and passive electronic components such as resistors and interconnections.
Porte logiquevignette|Composants TTL Une porte logique (gate) est un circuit électronique réalisant des opérations logiques (booléennes) sur une séquence de bits. Cette séquence est donnée par un signal d'entrée modulé en créneau (signal carré), et cadencé de façon précise par un circuit d'horloge, ou quartz. Les opérations logiques sont réalisées électriquement par une combinaison de bascules ou inverseurs, à base de transistors. Étant donné les capacités d'intégration en électronique, un circuit intégré comporte généralement plusieurs portes à la fois.
Electron mobilityIn solid-state physics, the electron mobility characterises how quickly an electron can move through a metal or semiconductor when pulled by an electric field. There is an analogous quantity for holes, called hole mobility. The term carrier mobility refers in general to both electron and hole mobility. Electron and hole mobility are special cases of electrical mobility of charged particles in a fluid under an applied electric field. When an electric field E is applied across a piece of material, the electrons respond by moving with an average velocity called the drift velocity, .
Hybrid integrated circuitA hybrid integrated circuit (HIC), hybrid microcircuit, hybrid circuit or simply hybrid is a miniaturized electronic circuit constructed of individual devices, such as semiconductor devices (e.g. transistors, diodes or monolithic ICs) and passive components (e.g. resistors, inductors, transformers, and capacitors), bonded to a substrate or printed circuit board (PCB). A PCB having components on a Printed Wiring Board (PWB) is not considered a true hybrid circuit according to the definition of MIL-PRF-38534.
Point-contact transistorThe point-contact transistor was the first type of transistor to be successfully demonstrated. It was developed by research scientists John Bardeen and Walter Brattain at Bell Laboratories in December 1947. They worked in a group led by physicist William Shockley. The group had been working together on experiments and theories of electric field effects in solid state materials, with the aim of replacing vacuum tubes with a smaller device that consumed less power.
Subthreshold conductionSubthreshold conduction or subthreshold leakage or subthreshold drain current is the current between the source and drain of a MOSFET when the transistor is in subthreshold region, or weak-inversion region, that is, for gate-to-source voltages below the threshold voltage. The amount of subthreshold conduction in a transistor is set by its threshold voltage, which is the minimum gate voltage required to switch the device between on and off states.
