Emission reduction by targeted transient <delta> operations in three-way catalysts for heavy-duty natural gas applications

To curb the severe effects of climate change, our society needs to radically reduce its CO2 footprint. For the heavy-duty sector, where electrification is difficult, alternative fuels can be the solution. Methane-fueled engines have lower energy-specific CO2 emissions than conventional Diesel-fueled engines. Furthermore, they have the potential of becoming carbon-neutral, when combined with bio-methane/synthetic methane. However, oxidation of unburnt methane in the exhaust gas poses a challenge for aftertreatment systems. The aim of this thesis is to investigate the mechanism of methane abatement and to reveal methods to reduce methane and other hazardous gas emissions. The majority of the experiments were conducted directly on an engine test bench, which is rarely seen in studies focusing on catalytic reaction pathways. Initial investigations focused on methane abatement under steady state and Î»-step transitions. Under steady state, the presence of oxygen was identified as a prerequisite for methane conversion. Reacting with oxygen is the only methane conversion pathway. However, after step transition from oxygen excess conditions (slightly lean) to oxygen-poor conditions (slightly rich), high methane conversion was observed under rich conditions with no oxygen available. This high conversion was attributed to steam reforming (SR), which was activated by the step transition. The SR reaction rate decreased over time when staying at rich conditions, until full deactivation. Investigations in the lab-scale model gas reactor confirmed this analysis. In addition, the reason for SR deactivation was identified by DRIFTS measurements as the accumulation of carbonates on the catalytic surface, blocking the active sites. Based on the identified importance of the SR reaction, targeted Î» oscillations across stoichiometry were introduced, in order to repeatably activate SR and achieve sustainable high methane conversion. During the rich parts of the oscillations, methane was converted via SR, while, during lean parts, the carbonates were periodically removed from the catalyst surface. With these oscillations, methane conversion has been significantly improved, in comparison to steady state. In parallel, a numerical model has been developed in order to simulate the catalyst behavior under oscillating conditions. The model provided insights on the reaction pathways and their distribution along the catalyst axis. The catalytic activity of the different Platinum-group metals has been investigated for the identified reactions. Various catalysts of different compositions were tested under cold start, Î» oscillations and quasi-steady state conditions. Both Pt and Pd activated SR reactions, however SR attenuation was faster in Pt catalysts. In lean conditions, Pt exhibited higher methane oxidation. Rh was identified as important for enhancing NOx reduction and lowering NH3 emissions. The combination of all three metals has improved the overall catalyst performances. In the final part of the thesis, a special aftertreatment system was investigated. It combines a Pd/Rh catalyst subject to stoichiometric conditions with a Pt oxidation catalyst subject to lean conditions. In the Pd/Rh catalyst, methane was removed via Î» oscillations. In the Pt catalyst, the remaining CO, H2 and NH3 were oxidized. The setup provided a novel perspective in reducing the overall environmental impacts.

Chemical and electrochemical promotion of supported rhodium catalyst

Olena Baranova

The chemical and electrochemical promotion of highly dispersed nanofilm Rh catalysts (dispersion: about 10 %, film thickness: 40 nm) has been investigated for the first time. To this end Rh metal was sputter-deposited, either on a purely ionic conductor (8 % Y2O3-stabilized ZrO2) or on a mixed ionic-electronic conductor (TiO2), the latter being a highly dispersed layer of TiO2 (4 µm) deposited on YSZ. These catalysts are designated as Rh/YSZ and Rh/TiO2/YSZ, respectively. It was established analytically that both in the Rh/YSZ and in the Rh/TiO2/YSZ system, the catalyst films have a nanoparticle-size grain structure. The Rh supported on titania is rather porous, exhibiting a higher dispersion and surface area than Rh on YSZ. Both after reduction (H2, T=400 °C) and after oxidation (O2, T=400 °C), Rh supported on TiO2 was found to be in a more highly reduced state than Rh on YSZ. After reducing treatment, the Rh/TiO2/YSZ samples contain a larger amount of weakly bonded oxygen, which can be attributed to oxygen "backspillover" from the TiO2. A major feature of this research was the electrochemical characterization of the oxygen/Rh/solid electrolyte three-phase boundary by steady-state polarization measurements and by impedance spectroscopy. These are powerful techniques for extracting experimental trends and details that are useful for an understanding of the electrochemical promotion principles. It was shown that the exchange current densities at the Rh/solid electrolyte interface are lower on account of the TiO2 layer. The exchange current densities are more than twice lower at Rh/TiO2(4 µm)/YSZ than at Rh/YSZ, demonstrating that the former interface is much more polarizable. The mechanism of oxygen exchange occurring close to equilibrium (O2/O2- couple) was investigated for the first time at Rh catalyst electrodes interfaced with solid electrolyte. The processes of cathodic oxygen reduction and anodic oxygen evolution are not symmetric, but they are similar in the two systems, Rh/YSZ and Rh/TiO2(4 µm)/YSZ. The cathodic process consists of three steps: dissociative adsorption of oxygen at the gas-exposed Rh surface, atomic oxygen diffusion to the electrochemical reaction sites (ERS), and a two-electron transfer to this oxygen on the ERS. The cathodic process is limited by interfacial diffusion of oxygen atoms from the gas-exposed metal surface to the ERS. The anodic process includes two steps: two-electron transfer reaction, which is the rate-determining step, and oxygen desorption to the gas phase. With data obtained from impedance spectroscopy at the equilibrium potential, it was possible to confirm the reaction scheme proposed. It was demonstrated that Rh nanofilm catalysts interfaced with YSZ or TiO2/YSZ can be electrochemically promoted for the reaction of ethylene oxidation. Small anodic currents cause periodic oscillations in catalytic rate and potential of the Rh/YSZ catalyst, while at Rh/TiO2/YSZ they give rise to a stable and reversible rate enhancement by up to a factor 80. The increase in ethylene oxidation rate is up to 2000 times larger than the electrochemical rate, I/2F, of O2- oxidation. The pronounced electrochemical promotion behavior that has been observed is due to the anodically controlled migration of O2- species from the electrolyte to the Rh/gas interface. At the Rh surface, these species destabilize the formation of rhodium surface oxide (Rh2O3). The existence of backspillover oxygen species has been confirmed by impedance measurements under positive applied potential. Another significant result for heterogeneous catalysis is the finding that thick as well as thin films of Rh/TiO2/YSZ catalyst are open to chemical promotion of ethylene oxidation and partial methane oxidation, ie, they offer a higher catalytic activity and stability than the Rh/YSZ catalysts. The modification of catalytic activity observed for Rh/TiO2/YSZ was attributed to either a "long-range" electronic-type SMSI mechanism or to a self-driven electrochemical promotion mechanism. In both cases, the ultimate cause of promotion are different work functions of catalyst and support. Equilibration of the work functions of two solids in contact induces surface charging, a migration of O2- ions to the catalyst/gas interface, and a weakening of the Rh-O chemisorptive bonds. It facilitates reduction of oxidized surface sites. Another important achievement of the present work was that of exploring and confirming the possibilities of current-assisted activation of Rh/TiO2/YSZ catalysts. In partial methane oxidation using close to stoichiometric gas compositions (CH4 : O2 = 2 : 1) at 550 °C, the inactive (oxidized) Rh/TiO2/YSZ catalyst was successfully activated by applied currents, either positive or negative. This phenomenon is an example of "permanent" electrochemical promotion furnishing a permanent rate enhancement ratio of γ = 11. The activation by negative currents is explained in terms of an electrochemical reduction of rhodium surface oxide, while the activation by positive currents can be explained by the mechanism of electrochemical promotion.

EPFL2005

Study of N2O decomposition over Fe-ZSM-5 with transient methods

Petra Prechtl

Nitrous oxide is the third most important gas contributing to global warming and its concentration in the atmosphere is still on the rise. Nitric acid production represents the largest source of N2O in the chemical industry, with a total annual emission of about 400 kt N2O. An efficient way to reduce the N2O is the catalytic decomposition into N2 and O2. ZSM-5 zeolites containing iron are known to be effective in this reaction involving Fe(II)-extraframework species as active sites. But the nature of these sites and the reaction network is still under debate. Often the N2O is in the exhaust together with other gases like NOx, COx, oxygen, and water vapor, which may influence the catalyst efficiency towards N2O decomposition. The effect of these gases on the reaction mechanism is still not understood yet. The aim of this work is to study the decomposition mechanism of N2O over isomorphously substituted Fe-ZSM-5 (0.02-0.55% Fe) using transient response methods. Kinetic studies under steady-state conditions give overall information about the reaction, whereas transient experiments lead to information on the individual steps and the possibility to suggest a reaction model. Transient response methods are applied in vacuum using a Temporal Analysis of Products (TAP) setup and at ambient pressure using a Micromeritics AutoChem 2910 analyzer. The influence of different gases such as NO, H2O and NO2 on the decomposition of N2O over Fe-ZSM-5 is investigated to gain insight into their effect on this reaction. The TAP multifunctional reactor system is used to perform transient pulse experiments for micro-kinetic analysis of complex heterogeneous catalytic reactions. This setup allows to dose precisely reactants and to monitor product formation with submillisecond time resolution implying the absence of external mass or heat transfer. A reproducible low hydroxylation level of the catalyst can be attained in vacuum. The results from the transient responses with the Micromeritics analyzer are obtained under conditions more relevant to "operando". The mechanism of N2O decomposition over Fe containing ZSM-5 was studied by transient response methods at ambient pressure with the Micromeritics analyzer and under vacuum with the TAP setup. Both approaches showed that the mechanism strongly depends on the reaction temperature, but in all cases involves atomic oxygen loading from N2O with N2 evolution as the first reaction step. The surface oxygen, (O)Fe, formed from N2O possesses very high reactivity and oxidizes CO to CO2 already at 373 K. A complete saturation of the active sites can be reached by the catalyst exposure to N2O at low temperatures (T < 600 K in vacuum, T < 523 K at ambient pressure). Under these conditions oxygen is stored and does not desorb. On that basis, the concentration of sites active for the surface atomic oxygen loading from N2O is determined by pulse experiments using the TAP setup. The concentration of active sites is found to be the same as in a flow experiment with the Micromeritics analyzer. The mechanism of surface atomic oxygen recombination and desorption as O2 depends on the temperature. At temperatures higher than 773 K, the mechanism probably involves direct (O)Fe recombination. The investigation of the response profiles upon N2O pulses at 803 K evidences the O2 formation is the rate-determining step since the oxygen desorption is found to be slow compared to N2O and N2. Furthermore, a fit of the oxygen desorption curve corresponded to a first order dependence on the oxygen surface coverage. In the range of 523 to 773 K, the O2 formation is facilitated by NO, which is formed on the catalyst surface from N2O. The addition of NO to the gas phase confirmed the accelerating effect of NO on the oxygen desorption. NO and (O)Fe are adsorbed on adjacent, but different sites and are not competing for the same ones. Adsorbed NO accommodates oxygen from N2O forming higher oxidized nitrogen oxide species NO2/NO3 which decompose back to NOads and molecular oxygen. Thus, the recombination of surface oxygen loaded from N2O is accelerated by a NO/NOx redox cycle whereas adsorbed NOx acts as co-catalyst. Adsorbed NO is oxidized by N2O easily as shown also by temperature-programmed desorption (TPD) experiments. Therefore, the interaction of gaseous NO2 with Fe-ZSM-5 at 523 K in vacuum and at ambient pressure is investigated and demonstrates the formation of two different NOx surface species accompanied by the evolution of gaseous NO. These surface species block the sites for oxygen loading from N2O whereas the amount of reversible adsorbed N2O stays constant compared to the standard pre-treated catalyst. The formation of reactive surface oxygen from NO2 could neither be evidenced in TPD nor with CO oxidation experiments. Adsorbed water strongly influences the N2O decomposition inhibiting it completely, at least at temperatures ≤ 673 K. Water pulses at 523 and 593 K result in partial desorption of the loaded atomic surface oxygen as O2, indicating the competition of water for the same adsorption sites. The residual adsorbed oxygen desorbs during TPD experiments at 849 K instead of 715 K for the dry catalyst and it can not oxidize CO to CO2. It means that the active sites are transformed into an inactive form in the presence of water. The oxygen which stays on the catalyst seems to participate in the Fe(II) oxidation to the hydroxylated Fe(III) species. These Fe(III) species are inactive in N2O decomposition and could be activated again by high temperature treatment in He or in vacuum. During TAP experiments only small amounts of water are dosed and the water desorption is facilitated due to vacuum. Therefore, the effect of water could be shown to be reversible at temperatures > 700 K. At 803 K oxygen desorbs significantly faster with increasing water amount suggesting a water assisted O2 desorption. Simultaneously, the catalyst activity decreases to about a half of the initial activity of the dry zeolite. To conclude, from the TAP reactor data obtained under vacuum conditions and the results from the transient flow experiments at ambient pressure it follows that the mechanism of the N2O decomposition over Fe-containing ZSM-5 depends strongly on the reaction temperature and on the presence of NO, H2O and NO2. In general, below 523 K only surface atomic oxygen loading from N2O takes place with simultaneous evolution of N2 in the gas phase. The O2 formation proceeds via direct (O)Fe recombination at temperatures above 773 K. In the range of 523 to 773 K, the recombination of the atomic oxygen involves NOx adsorbed on the catalyst surface.

EPFL2007

Nitrous Oxide Abatement over Fe-Zeolite

Bryan Bromley

The use of zeolites for catalytic reactions is a field in continuous development. Since it was demonstrated that metal-zeolites are efficient catalysts for NOx abatement, decomposition of nitrous oxide (N2O) over Fe-containing zeolites has attracted great interest by the scientific community mainly due: N2O is the third most important gas contributing to global warming, its concentration in atmosphere is still on the rise and direct N2O decomposition to N2 and O2 is a sustainable alternative. N2O interaction with Fe-zeolite leads to the formation of "special" adsorbed oxygen (often called α-oxygen) with great potential for selective oxidation. Although the focus of a number of studies, the nature of the actives sites for the formation of this adsorbed oxygen is still unclear. The main objectives of this work are: 1) study the decomposition mechanism of N2O over isomorpously substituted Fe-ZSM-5 zeolite aiming on catalyst optimization and 2) optimization and further use of structured Fe-zeolite in novel micro-structured reactor. A number of refined transient kinetics methods were intensively used such as transient response, Temperature Programmed Desorption (TPD) and Temporal Analysis of Product (TAP). Density Functional Theory (DFT) and in situ IR spectroscopy studies were conducted in collaboration and our results support the following: In chapter 3, quantitative measurements have been carrier out to analyze the effect of temperature on the activation (under helium flow) and the irreversible deactivations that can happen during the pretreatment. The results obtained indicate that high temperature treatment (1273 K) results in the formation of a high amount of α-sites. The addition of a very low fraction of oxygen (2%) in the feed demonstrates that the catalyst is sensitive to its presence. Certain sites can be irreversibly destroyed, a result ascribed to the oxidation of active Fe(II) to Fe2O3 clusters which contain inactive Fe(III). Catalyst treatment at high temperature (1273 K) in He for up to 3 hours, also reduced irreversibly the concentration of α-sites. TPD measurements have shown desorption of oxygen at 3 different temperatures. Desorption at the lowest temperature (650 K) was assign to the α-oxygen recombination. The oxygen which desorbs at 700 K was associated to the oxygen from the deactivated sites. Oxygen which desorbs at the highest temperature (730 K) is originated from the surface NOx that desorbed as NO and O2. After a comparison of the concentration of the molecules accumulated, we propose that NO2 is the adsorbed specie. The mechanism of N2O decomposition on the binuclear oxo-hydroxo bridged extraframework iron core site [FeII(μ-O)(μ-OH)FeII]+ inside the ZSM-5 zeolite has been studied by combining theoretical and experimental approaches (see chapter 4). Rate parameters computed using standard statistical mechanics and transition state theory reveal that elementary catalytic steps involved into N2O decomposition are strongly dependent on the temperature. This theoretical result was contrasted with the experimentally observed steady state kinetics of the N2O decomposition and TPD experiments. As predicted by the theoretical study, the switch of the reaction order with respect to N2O pressure (from zero to one) occurs at around 800 K which confirms a change of the rate determining step from the α-oxygen recombination to α-oxygen formation. The proposed mechanism was also confirmed by O2-TD which confirmed the viability of the binuclear complex. The α-oxygen recombination at low temperature (

EPFL2010