Publication

Hydraulic Transport Through Calcite Bearing Faults With Customized Roughness: Effects of Normal and Shear Loading

Abstract

Understanding fluid flow in rough fractures is of high importance to large scale geologic processes and to most anthropogenic geo‐energy activities. Here we conducted fluid transport experiments on Carrara marble fractures with a novel customized surface topography. Transmissivity measurements were conducted under mechanical loading conditions representative of deep geothermal reservoirs (normal stresses from 20 to 70 MPa and shear stresses from 0 to 30 MPa). A numerical procedure simulating normal contact and fluid flow through fractures with complex geometries was validated toward experiments. Using it, we isolated the effects of roughness parameters on fracture fluid flow. Under normal loading, we find that (i) the transmissivity decreases with normal loading and is strongly dependent on fault surface geometry and (ii) the standard deviation of heights (hRMS) and macroscopic wavelength of the surface asperities control fracture transmissivity. Transmissivity evolution is nonmonotonic, with more than 4 orders of magnitude difference for small variations of macroscopic wavelength and hRMS roughness. Reversible elastic shear loading has little effect on transmissivity; it can increase or decrease depending on contact geometry and overall stress state on the fault. Irreversible shear displacement (up to 1 mm offset) slightly decreases transmissivity and its variation with irreversible shear displacements can be predicted numerically and geometrically at low normal stress only. Finally, irreversible changes in surface roughness (plasticity and wear) due to shear displacement result in a permanent decrease of transmissivity when decreasing differential stress. Generally, reduction of a carbonate fault's effective stress increases its transmissivity while inducing small shear displacements does not.

About this result
This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.
Related concepts (36)
Stress (mechanics)
In continuum mechanics, stress is a physical quantity that describes forces present during deformation. An object being pulled apart, such as a stretched elastic band, is subject to tensile stress and may undergo elongation. An object being pushed together, such as a crumpled sponge, is subject to compressive stress and may undergo shortening. The greater the force and the smaller the cross-sectional area of the body on which it acts, the greater the stress. Stress has units of force per area, such as newtons per square meter (N/m2) or pascal (Pa).
Cauchy stress tensor
In continuum mechanics, the Cauchy stress tensor , true stress tensor, or simply called the stress tensor is a second order tensor named after Augustin-Louis Cauchy. The tensor consists of nine components that completely define the state of stress at a point inside a material in the deformed state, placement, or configuration. The tensor relates a unit-length direction vector e to the traction vector T(e) across an imaginary surface perpendicular to e: or, The SI units of both stress tensor and traction vector are N/m2, corresponding to the stress scalar.
Shear stress
Shear stress (often denoted by τ (Greek: tau)) is the component of stress coplanar with a material cross section. It arises from the shear force, the component of force vector parallel to the material cross section. Normal stress, on the other hand, arises from the force vector component perpendicular to the material cross section on which it acts. The formula to calculate average shear stress is force per unit area.: where: τ = the shear stress; F = the force applied; A = the cross-sectional area of material with area parallel to the applied force vector.
Show more
Related publications (290)

Frictional weakening leads to unconventional singularities during dynamic rupture propagation

Marie Estelle Solange Violay, Mathias Alexandre David Lebihain, François Xavier Thibault Passelègue, Federica Paglialunga

Earthquakes i.e. frictional ruptures, are commonly described by singular solutions of shear crack motions. These solutions assume a square root singularity order around the rupture tip and a constant shear stress value behind it, implying scale-independent ...
2024

Proliferation-driven mechanical compression induces signalling centre formation during mammalian organ development

Sangwoo Kim, Pengfei Xu

Localized sources of morphogens, called signalling centres, play a fundamental role in coordinating tissue growth and cell fate specification during organogenesis. However, how these signalling centres are established in tissues during embryonic developmen ...
Nature Portfolio2024

Single-Well Pore Pressure Preconditioning for Enhanced Geothermal System Stimulation

Marie Estelle Solange Violay, Mathias Alexandre David Lebihain, Barnaby Padraig Fryer

The stress state is an important parameter in terms of both earthquake nucleation and rupture. Here, a new stimulation technique is proposed for Enhanced Geothermal Systems (EGSs), which have previously been burdened with a number of high-profile incidence ...
AMER GEOPHYSICAL UNION2023
Show more
Related MOOCs (16)
Plasma Physics: Introduction
Learn the basics of plasma, one of the fundamental states of matter, and the different types of models used to describe it, including fluid and kinetic.
Plasma Physics: Introduction
Learn the basics of plasma, one of the fundamental states of matter, and the different types of models used to describe it, including fluid and kinetic.
Plasma Physics: Applications
Learn about plasma applications from nuclear fusion powering the sun, to making integrated circuits, to generating electricity.
Show more

Graph Chatbot

Chat with Graph Search

Ask any question about EPFL courses, lectures, exercises, research, news, etc. or try the example questions below.

DISCLAIMER: The Graph Chatbot is not programmed to provide explicit or categorical answers to your questions. Rather, it transforms your questions into API requests that are distributed across the various IT services officially administered by EPFL. Its purpose is solely to collect and recommend relevant references to content that you can explore to help you answer your questions.