A subwoofer (or sub) is a loudspeaker designed to reproduce low-pitched audio frequencies known as bass and sub-bass, lower in frequency than those which can be (optimally) generated by a woofer. The typical frequency range for a subwoofer is about 20–200 Hz for consumer products, below 100 Hz for professional live sound, and below 80 Hz in THX-certified systems. Thus one or more subwoofers are important for high quality sound reproduction as they are responsible for the lowest two to three octaves of the ten that are audible. This very low-frequency (VLF) range reproduces the natural fundamental tones of the bass drum, electric bass, double bass, grand piano, contrabassoon, tuba, in addition to thunder, gunshots, explosions, etc.
Subwoofers are never used alone, as they are intended to substitute the VLF sounds of "main" loudspeakers that cover the higher frequency bands. VLF and higher frequency signals are sent separately to the subwoofer(s) and mains by a "crossover" network, typically using active electronics, including digital signal processing (DSP). Additionally, subwoofers are fed their own low frequency enhancement (LFE) signals that are reproduced at 10 dB higher than standard peak level.
Subwoofers can be positioned more favorably than the main speakers' woofers in the typical listening room acoustic, as the very low frequencies they reproduce are nearly omnidirectional and their direction largely indiscernible. However much digitally recorded content contains lifelike binaural cues that human hearing may be able to detect in the VLF range, reproduced by a stereo crossover and two or more subwoofers. Subwoofers are not acceptable to all audiophiles, likely due to distortion artifacts produced by the subwoofer driver after the crossover and at frequencies above the crossover.
While the term "subwoofer" technically only refers to the speaker driver, in common parlance, the term often refers to a subwoofer driver mounted in a speaker enclosure (cabinet), often with a built-in amplifier.
This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.
Ce cours a pour objectif de former les étudiants de section Génie Electrique et Electronique à la conception de systèmes acoustiques, à l'aide d'un formalisme basé sur l'électrotechnique. A la fin du
This lecture is oriented towards the study of audio engineering, with a special focus on room acoustics applications. The learning outcomes will be the techniques for microphones and loudspeaker desig
A loudspeaker (commonly referred to as a speaker or speaker driver) is an electroacoustic transducer that converts an electrical audio signal into a corresponding sound. A speaker system, also often simply referred to as a speaker or loudspeaker, comprises one or more such speaker drivers, an enclosure, and electrical connections possibly including a crossover network. The speaker driver can be viewed as a linear motor attached to a diaphragm which couples that motor's movement to motion of air, that is, sound.
A sound reinforcement system is the combination of microphones, signal processors, amplifiers, and loudspeakers in enclosures all controlled by a mixing console that makes live or pre-recorded sounds louder and may also distribute those sounds to a larger or more distant audience. In many situations, a sound reinforcement system is also used to enhance or alter the sound of the sources on the stage, typically by using electronic effects, such as reverb, as opposed to simply amplifying the sources unaltered.
An audio power amplifier (or power amp) is an electronic amplifier that amplifies low-power electronic audio signals, such as the signal from a radio receiver or an electric guitar pickup, to a level that is high enough for driving loudspeakers or headphones. Audio power amplifiers are found in all manner of sound systems including sound reinforcement, public address, home audio systems and musical instrument amplifiers like guitar amplifiers. It is the final electronic stage in a typical audio playback chain before the signal is sent to the loudspeakers.
The acoustics of a room often refer to the quality of the room in terms of sound recording as well as sound reproduction. At low frequencies, where the wavelengths are of the same order of magnitude with the dimensions of the room, due to the standing wav ...
La construction de tours en Suisse a été constamment sujette à de nombreux débats et ce, depuis son apparition au milieu du siècle dernier. L’énoncé théorique a permis d’identifier les principales limites qui tendent à marginaliser ce type de « monolithe » ...
Sound absorption at low frequencies still remains a challenge in both scientific research and engineering practice. Natural porous materials are ineffective in this frequency range, as well as acoustic resonators which present too narrow bandwidth of absor ...