Rectifier | EPFL Graph Search

A rectifier is an electrical device that converts alternating current (AC), which periodically reverses direction, to direct current (DC), which flows in only one direction. The reverse operation (converting DC to AC) is performed by an inverter. The process is known as rectification, since it "straightens" the direction of current. Physically, rectifiers take a number of forms, including vacuum tube diodes, wet chemical cells, mercury-arc valves, stacks of copper and selenium oxide plates, semiconductor diodes, silicon-controlled rectifiers and other silicon-based semiconductor switches. Historically, even synchronous electromechanical switches and motor-generator sets have been used. Early radio receivers, called crystal radios, used a "cat's whisker" of fine wire pressing on a crystal of galena (lead sulfide) to serve as a point-contact rectifier or "crystal detector". Rectifiers have many uses, but are often found serving as components of DC power supplies and high-voltage dire

High voltage power supply system for tethered drone part II

Clément Bongini

A high voltage power supply system for a tethered drone is presented. The project is a follow-up to a previous semester project and the purpose of this project is to review the implementation, improve the design and solve problems. The system consists of an inverter part, a transformer part and a rectifier part. The input voltage is 600 VDC and the output voltage is 12VDC for a maximum power of 1500W. The inverter part is composed of 4 transistors controlled by two gate drivers. On the other side of the transformer, we have a bridge rectifier which will be implemented in 3 different ways: a full-bridge diode and two new active rectification systems, including mosfets and controllers. We will first present the different systems chosen, review the previous part and make improvements, then we will implement these new systems, design the prototypes and make tests for each system. Finally, we will test the whole converter.

2021

An Efficient Piezoelectric Energy Harvesting Interface Circuit Using a Sense-and-Set Rectifier

Yimai Peng

Piezoelectric energy harvesters (PEHs) are widely deployed in many self-sustaining systems, and proper rectifier circuits can significantly improve the energy conversion efficiency and, thus, increase the harvested energy. Various active rectifiers have been proposed in the past decade, such as synchronized switch harvesting on inductor (SSHI) and synchronous electric charge extraction (SECE). This article presents a sense-andset (SaS) rectifier that achieves maximum-power-point-tracking (MPPT) of PEHs and maintains optimal energy extraction for different input excitation levels and output voltages. The proposed circuit is fabricated in the 0.18-μm CMOS process with a 0.47-mm 2 core area, a 230-nW active power, and a 7-nW leakage power. Measured with a commercial PEH device (Mide PPA-1022) at 85and 60-Hz vibration frequency, the proposed circuit shows 512% and 541% power extraction improvement [figure of merit (FoM)] compared with an ideal full-bridge rectifier (FBR) for ON-resonance and OFF-resonance vibrations, respectively, while maintaining high efficiency across different input levels and PEH parameters.

IEEE2019

Analysis and optimization of passive UHF RFID systems

Jari-Pascal Curty

Radio Frequency IDentification (RFID) is an automatic identification method, relying on storing and remotely retrieving data using devices called RFID tags or transponders. An RFID tag is a small object that can be attached to or incorporated into a product, animal or person. RFID tag contains antenna to enable it to receive and respond to Radio-Frequency (RF) queries from an RFID reader or interrogator. Passive tags require no internal power source, whereas active tags require a power source. As of today (2005), the ubiquitous computing and ambient intelligence ideas are making their way. In order for these to become a reality, a number of key technologies are required. Briefly, these technologies need to be sensitive, responsive, interconnected, contextualised, transparent and intelligent. RFID is such a technology and more particularly passive RFID tags. But, in order to deliver the necessary characteristics that could trigger ambient intelligence, there are some challenges that need to be addressed. Remote powering of the tags is probably the most important. Issues concerning the antenna-tag interface, as well as the rectifier design, that allows the RF signal to be converted to Direct Current (DC) are in pole position. Secondly, the communication link and the reader should be optimized. The RF signal that contains the tag data suffers from a power of four decay with the distance between tag and reader. As a result, both the reader sensitivity and the tag backscattered power efficiency have to be maximized. Long-range powering, as well as sufficient communication quality, are the guidelines of this work. This research project proposes a linear two-port model for an N-stage modified-Greinacher full wave rectifier. It predicts the overall conversion efficiency at low power levels where the diodes are operating near their threshold voltage. The output electrical behavior of the rectifier is calculated as a function of the received power and the antenna parameters. Moreover, the two-port parameters values are computed for particular input voltages and output currents for the complete N-stage rectifier circuit using only the measured I-V and C-V characteristics of a single diode. Also presented in this work is an experimental procedure to measure how the impedance modulation at the tag side affects the signal at the reader. The method allows the tag designer to efficiently predict the effect of modulator design at system level and gives an useful instrument to choose the most appropriate impedances. Finally, the design of a fully integrated remotely powered and addressable RFID tag working at 2.45 GHz is described. The achieved operating range at 4 W Effective Isotropically Radiated Power (EIRP) reader transmit power is 12 m. The Integrated Circuit (IC) is implemented in a 0.5 μm silicon-on-sapphire technology. A state of the art rectifier design achieving 37% of global efficiency is embedded to supply energy to the transponder. Inductive matching and a folded-dipole antenna are key elements to achieve these performances. The necessary input power to operate the transponder is about 2.7 μW.

EPFL2006

Analysis and optimization of passive UHF RFID systems

Jari-Pascal Curty

EPFL2006