Analysis and Design of Ultra-Wideband Antennas in the Spectral and Temporal Domains

Formal research on Ultra-wideband (UWB) technology started in the U.S. in 2002; where its definition was formulated and the frequency allocation in that country established. However, the first ultra-wideband transmission was done during the confirmation of Maxwell's equations by Heinrich Hertz in 1886, the first ever reported radio transmission. Sparks or very short pulses were sent and received at a distance away from its source. UWB antennas have existed since those times, but technology has been mostly focused on the transmission of continuous wave narrowband signals. The largest problematic encountered in today's UWB antennas is that characterization methods were, since the beginning, meant to describe narrowband antennas. The frequency characteristics of these antennas are constant over their operational bandwidth, hence they can be fully characterized in the frequency domain. UWB antennas, on the other hand, are meant to transmit pulsed signals. Analyzing them only in the frequency domain is not enough to fully evaluate their performance, as pulse distortion is an important parameter that should be controlled. An extended literature review is included in the first part of this thesis, where the available UWB antenna characterization methods are evaluated. Many limitations were encountered, showing that the available techniques do not analyze simultaneously the most important parameters of an UWB antenna. A new characterization method is proposed: the System Fidelity Factor (SFF). Its main purpose is to incorporate frequency, time and space characteristics of a two-antennas system to compare UWB antennas in an efficient way. This is achieved with the correlation between the received and the input pulses, quantifying the distortion produced by the system. The SFF is an interesting tool because both simulations and measurements can be done in a simple and straight-forward manner, using tools that are commonly available in any antenna lab. Any combination of antennas can be analyzed and the free-space channel can be easily replaced with any other environment. Several UWB antennas were designed and used to prove the efficiency of the SFF. A good agreement between the proposed simulation techniques and the measurements was achieved. The antennas are novel designs specially developed for UWB applications under the American or European regulations. The last part of the thesis presents these antennas and analyzes them using the SFF to compare their performance.

A simple & [and] accessible front-end satellite receiver for communications and e-learning in emerging countries

Olivier Videme Bossou

For the universities of the emergent countries, and those of Cameroon in particular, the fight to reach a durable development requires to know the needed scientific and technical information for their development, how to get it and to spread it out among partners in the country. Obviously, the complete answer to these preoccupations lies well beyond the framework of this project, but a projection, partial but highly significant, can nevertheless be obtained if one concentrates one's efforts on a specific technological field : in the present study, we shall treat of antennas for telecommunications systems. This subject is highly suitable as example and potential incubator for future achievements. The ultimate goal is to design and carry out the fabrication of a system of satellite communications adapted to the financial resources and to the development needs of the universities of the South. First of all, we will review the state of the art in satellite communication systems, both for already operating ones and also for new systems, still under development. Then we will determine which system of satellite telecommunications has a receiver and communication fees with affordable costs : our choice will be made on Worldspace satellite system, which was actually designed for developing countries. We will also review the status of planar antenna and low noise amplifier technology, and then explicit the basic challenge involved in our thesis project. One of the aims of this project is to use local wood as dielectric in SSFIP type antennas. Before using a material as dielectric in an antenna design, it must be characterized. Before carrying the characterization of local wood species, we will begin by reviewing some commonly used dielectric measurement techniques. Then we will carry out a series of measurements to characterize the species of wood growing in the Cameroonian forest. At the end of the series of measurements and according to the dielectric losses observed, we will select the species of wood best suited to make a good substrate for a microstrip antenna. Next, we will design, manufacture and test low cost antennas. These antennas must satisfy not only technical criteria compatible with those of the telecommunications system chosen but, even most importantly, it must meet socioeconomic criteria : the antennas must be manufactured with low cost and locally available materials, making use of simple technological processes. Once we have found the wood species that exhibits the lowest dielectric losses, we will simulate, and then manufacture the SSFIP type antenna with wood as substrate and aluminium as conducting element. Then we will measure its characteristics and check whether they are compatible with those of a Worldspace receiver. The signal received from the satellite by the antenna is very weak. It will be important to strengthen the received signal with a low noise amplifier (LNA) before connecting the antenna to the receiver. Thus the antenna and the LNA constitute an active antenna and form what we call here the radiofrequency (RF) front-end. We will design, manufacture and measure the LNA characteristics. A simple manufacturing process must be used to realize these antennas, because later on they must be manufactured locally in Cameroon : this is a determining challenge to ensure the economic independence, which is essential in our thesis project. Afterwards we will join the LNA to the planar antenna and connect the active antenna obtained in this manner to a commercial Worldspace receiver. Finally, we will perform receiving tests of the Worldspace radio station with the system designed. In parallel, our project includes a second goal, which presents an equivalent significance. We will use existing Matlab codes to develop an online course to teach antenna theory. In addition, at the end of the project and when the Cameroonian local manufacture would have started, we will put all algorithms used for the antenna design on the web site in a multi-media applet, together with a complete documentation of all the manufacturing technologies used. The courses that already exist in Lausanne and Yaounde, relating to the description of other types of antennas will be added, thus leading to a complete teachware that would ensure the durability and the dissemination of the results obtained, and would provide an invaluable tool for teaching and training.

EPFL2007

Compensation des non-linéarités des systèmes haut-parleurs à pavillon

Delphine Bard

The assumptions of linearity and autonomy assumed in circuit theory are known to be respected only partially by electroacoustic transducers. In particular, the dynamics range of the latter is limited by the audible nonlinear effects that they are causing. In the domain of active noise control, the distortion products limit noise reduction performance. The present thesis work stems from characterization of these observations. We want to design a real-time system compensating the nonlinearities of electroacoustic devices. The first part of this report concerns the nonlinearity effects. It is shown that the use of classical characterization methods of an electroacoustic device (harmonic distortion, intermodulation, frequency difference ...) is limited. Hence, they can not be used to determine the nonlinearity laws themselves, but rather only their effects for arbitrary excitations. First, a method based on multitone harmonic excitations has been proposed and validated. It has been applied for the characterization of loudspeaker prototypes using several different technologies, which are used for active noise reduction in an aircraft turboreactor. The second part of this work addresses the elaboration and validation of a nonlinearity effect compensation method. This method is based on the description of the nonlinearities by the Volterra series. For this, we need to place an upstream system, characterized by the inverse nonlinearity law of the loudspeaker system. After having determined precisely the Volterra kernels of the system to be characterized, the kernels of the upstream compensation system are determined by assuming that their cascade obeys to a linear law. For this purpose, a kernel measurement method in the frequency domain has been developed, validated and tested. Since we are concerned with loudspeakers, we took their flying time into account. The compensation method has been validated by computing the simulated response of the compensation circuit. Resulting analog signals have then been applied to the loudspeaker. Measured performances fulfill the expectations. In the last part, the compensation method has been applied in a real-time Digital Signal Processing) DSP controller, which allowed to realize a demonstrator to the implemented for future industrial applications.

EPFL2005

System Fidelity Factor: a new method for comparing UWB antennas

Gabriela Quintero Diaz De Leon, Anja Skrivervik Favre, Jean-François Zürcher

The main purpose of the System Fidelity Factor (SFF) is to incorporate frequency and time domain characteristics of an antenna system into a comparison method for ultrawideband (UWB) antennas. The SFF is an interesting tool because both simulations and measurements can be done in a simple and straight-forward manner. Simulations of a single antenna are combined into a two-antennas system analysis by means of a simple post-processing, where the transfer function of the transmitting and receiving antennas are calculated. Measurements of the SFF are done using a two port Vector Network Analyzer (VNA). The polar representation of the SFF allows an equitable comparison between antennas. The procedure to derive the SFF is described in detail in the paper. Two examples are given where the UWB performance of three antenna systems are compared. In the first example antenna systems of two identical monopoles are studied. In the second example the transmitting antenna is a Vivaldi and the receiving antenna a monopole.