Publications associées à Ampèremètre

Segmented Spiral Using Inter-Connected Timber Elements

Yves Weinand, Aryan Rezaei Rad, Petras Vestartas, Martin Thomas Nakad, Loïc Henri Pelletier

This paper describes the construction process of a scenographic structure - five meters high spiral. It consists of following parts: CAD modeling work-flow, prototyping and FEM structural calculation, assembly and on-site loading test. The structure was co ...

INT CENTER NUMERICAL METHODS ENGINEERING2019

Investigation of RF Nb-Ti PF 1&6 Coils Conductor Performances in the SULTAN Test Facility

Pierluigi Bruzzone, Boris Stepanov

This paper summarizes the work on the manufacturing and testing of conductor samples for ITER poloidal field 1&6 coils. The work was carried out by the IO and multiple institutions in the EU, Switzerland and Russia. Five samples were manufactured and teste ...

IEEE Institute of Electrical and Electronics Engineers2017

Compact and General Strategy for Solving Current and Potential Distribution in Electrochemical Cells Composed of Massive Monopolar and Bipolar Electrodes

Hubert Girault, Alejandro Nicolás Colli

A compact, fast and general algorithm based on Dirichlet boundary conditions for the potential field is derived to enable the calculation of local current distribution, shunt currents and the local potential distribution on massive electrodes in electroche ...

2017

Performance of ITER Correction Busbar Conductor Samples CBCN2 and CBCN3

Pierluigi Bruzzone, Kamil Sedlák, Boris Stepanov, Fang Liu, Bo Liu

The correction busbar (CB) conductors for the ITER project are being produced in China. The second China CB conductor sample (CBCN2, Phase II of conductor testing) and the third CB conductor sample (CBCN3, Phase III testing) were made of the WST NbTi stran ...

IEEE Institute of Electrical and Electronics Engineers2016

Superior GRAPPA reconstruction with reduced g-factor noise using 2D CAIPIRINHA for 3D EPI

Rolf Gruetter, José Pedro Rebelo Ferreira Marques, Mayur Narsude, Daniel Gallichan

Efficient GRAPPA or SENSE reconstruction is largely dependent on coil geometry in the direction in which phase encoding steps reduction is performed during partially parallel acquisition. In this study we demonstrate the ability to perform a 2D CAIPIRINHA ...

2013

Electroacoustic absorbers: Bridging the gap between shunt loudspeakers and active sound absorption

Romain Christophe Rémy Fleury, Hervé Lissek, Romain Boulandet

The acoustic impedance at the diaphragm of an electroacoustic transducer can be varied using a range of basic electrical control strategies, amongst which are electrical shunt circuits. These passive shunt techniques are compared to active acoustic feedbac ...

Acoustical Society of America2011

Electroacoustic absorbers I: bridging a gap between active acoustic feedback control and shunt loudspeakers

Hervé Lissek, Romain Christophe Rémy Fleury, Romain Boulandet

Variable acoustic properties can be obtained at the diaphragm of an electroacoustic transducer, with the help of very basic control strategies, among which is the simple electrical shunting of the transducer. These shunt techniques are compared to active a ...

2011

Modeling and Control of a Magnetically Levitated Planar Motor

Alireza Karimi, Roland Longchamp, Marc Kunze, Vincent Reymond

This paper deals with the modeling and control of a magnetically levitated planar motor. The actuator considered has moving coils and stationary magnets. The principal objective is to develop a model which can be implemented in simulation. Therefore, the d ...

2009

Pico-Watt Source-Coupled Logic Circuits

Seyed Armin Tajalli, Yusuf Leblebici

This article explores the main tradeoffs in design of subthreshold source-couple logic (STSCL) circuits. It is shown analytically that the bias current of each STSCL gate can be reduced to few pico-amperes with a reliable logic operation. Measurements on d ...

2008

Three-Axis Teslameter with Integrated Hall Probe

Radivoje Popovic, Pavel Kejik, Enrico Schurig

The first commercially available teslameter with a fully integrated three-axis Hall probe is described. The Hall probe chip contains horizontal and vertical Hall elements, analog electronics, and a synchronization circuit. A horizontal Hall element measure ...

Institute of Electrical and Electronics Engineers2007