Ultra Low Power Switched Current Finite Impulse Response Filter Banks Realized in CMOS 0.18 um technology

Ultra low power circuits are in high demand in many applications especially in wireless sensor networks (WSN), where energy is scavenged from environment. WSN systems contain different blocks, such as: sensors, filters, analog-to-digital converters, very often a simple processor and the RF front end block. This paper concerns ultra low power finite impulse response (FIR) filters and filter banks implemented in a switched current (SI) technique. In this paper new SI FIR filter structures and filter banks have been proposed. These circuits operate in the current mode and do not use operational amplifiers, what enables very low power dissipation on the level of several μW. Proposed filters incorporate transistors working under threshold level for the voltage supply that is in the range 0.5 – 0.7 V. The simulated attenuation in the stopband of the frequency response is limited to about 45 dB, what is due to different nonidealities, but such value is usually sufficient in WSN applications. The SI technique features many interesting mechanisms that simplify realization of analog filter banks. The signal samples that are stored in the delay lane are in SI filters copied to the filter coefficients using current mirrors. As a result, there exists the possibility to connect many sets of filter coefficients to a single delay line without the speed limitation. Ultra low power operation of proposed filters is also possible due to a special structure of the clock generator that only consists from switches and NOT gates.

Hybrid continuous-discrete-time multi-bit delta-sigma A/D converters with auto-ranging algorithm

Sergio Pesenti

In wireless portable applications, a large part of the signal processing is performed in the digital domain. Digital circuits show many advantages. The power consumption and fabrication costs are low even for high levels of complexity. A well established and highly automated design flow allows one to benefit from the constant progress in CMOS technologies. Moreover, digital circuits offer robust and programmable signal processing means and need no external components. Hence, the trend in consumer electronics is to further reduce the part of analog signal processing in the receiver chain of wireless transceivers. Consequently, analog-to-digital converters with higher resolutions and bandwidths are constantly required. The ultimate goal is the direct digitization of radio frequency signals, where the conversion would be performed immediately after the front-end amplifier. ΔΣ-modulation-based converters have proved to be the most suitable to achieve the required performance. Switched-capacitor implementations have been widely used over the last two decades. However, recent publications and books have shown that continuous-time architectures can achieve the same performance with lower power consumption. Most designs found throughout the literature use a single- or few-bit internal quantizer with a high-order modulation. As a result, in order to achieve the resolutions and bandwidths required today, the sampling frequency must exceed 100MHz. This approach leads to non-negligible power consumption in the clock generation. Moreover, the presence of such fast squared signals is not suitable for a system-on-chip comprising radio frequency receivers. In this thesis we propose a low-power strategy relying on a large number of internal levels rather than on a high sampling frequency or modulation order. Besides, a hybrid continuous-discrete-time approach is used to take advantage of the accuracy of switched-capacitor circuits and the low power consumption of continuous-time implementation. The sensitivity to clock jitter brought about by the continuous-time stage is reduced by the use of a large number of levels. An auto-ranging algorithm is developed in this thesis to overcome the limitation of a large-size quantizer under low-voltage supply. Finally, the strategy is applied to a design example addressing typical specifications for a Bluetooth receiver with direct conversion.

EPFL2007

0.35 μm 22μW Multiphase Programmable Clock Generator for Circular Memory SC FIR Filter For Wireless Sensor Applications

Rafal Tomasz Dlugosz

The paper presents the programmable multiphase clock generator for switched-capacitor finite impulse response (SC FIR) circular memory filters. The proposed programmable clock circuit enables easy division of such kind of filters into different orders smaller sections, which when connected in series, lead to increase in filter efficiency: reduction of chip area, power dissipation, and rising up of the speed. The proposed clock generator enables adjustment of the impulses width, that simplifies design process and leads to structure, which is more robust to process variation. The clock circuit realized in CMOS 0.35μm technology, dissipates 22 μW from 2 V power supply.

2006

Hybrid continuous-discrete-time multi-bit delta-sigma A/D converters with auto-ranging algorithm

Sergio Pesenti

EPFL2007