Thermal analysis is a branch of materials science where the properties of materials are studied as they change with temperature. Several methods are commonly used – these are distinguished from one another by the property which is measured:
Dielectric thermal analysis: dielectric permittivity and loss factor
Differential thermal analysis: temperature difference versus temperature or time
Differential scanning calorimetry: heat flow changes versus temperature or time
Dilatometry: volume changes with temperature change
Dynamic mechanical analysis: measures storage modulus (stiffness) and loss modulus (damping) versus temperature, time and frequency
Evolved gas analysis: analysis of gases evolved during heating of a material, usually decomposition products
Isothermal titration calorimetry
Isothermal microcalorimetry
Laser flash analysis: thermal diffusivity and thermal conductivity
Thermogravimetric analysis: mass change versus temperature or time
Thermomechanical analysis: dimensional changes versus temperature or time
Thermo-optical analysis: optical properties
Derivatography: A complex method in thermal analysis
Simultaneous thermal analysis generally refers to the simultaneous application of thermogravimetry and differential scanning calorimetry to one and the same sample in a single instrument. The test conditions are perfectly identical for the thermogravimetric analysis and differential scanning calorimetry signals (same atmosphere, gas flow rate, vapor pressure of the sample, heating rate, thermal contact to the sample crucible and sensor, radiation effect, etc.). The information gathered can even be enhanced by coupling the simultaneous thermal analysis instrument to an Evolved Gas Analyzer like Fourier transform infrared spectroscopy or mass spectrometry.
Other, less common, methods measure the sound or light emission from a sample, or the electrical discharge from a dielectric material, or the mechanical relaxation in a stressed specimen. The essence of all these techniques is that the sample's response is recorded as a function of temperature (and time).
This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.
Thermogravimetric analysis or thermal gravimetric analysis (TGA) is a method of thermal analysis in which the mass of a sample is measured over time as the temperature changes. This measurement provides information about physical phenomena, such as phase transitions, absorption, adsorption and desorption; as well as chemical phenomena including chemisorptions, thermal decomposition, and solid-gas reactions (e.g., oxidation or reduction). Thermogravimetric analysis (TGA) is conducted on an instrument referred to as a thermogravimetric analyzer.
Differential thermal analysis (DTA) is a thermoanalytic technique that is similar to differential scanning calorimetry. In DTA, the material under study and an inert reference are made to undergo identical thermal cycles, (i.e., same cooling or heating programme) while recording any temperature difference between sample and reference. This differential temperature is then plotted against time, or against temperature (DTA curve, or thermogram). Changes in the sample, either exothermic or endothermic, can be detected relative to the inert reference.
Dynamic mechanical analysis (abbreviated DMA) is a technique used to study and characterize materials. It is most useful for studying the viscoelastic behavior of polymers. A sinusoidal stress is applied and the strain in the material is measured, allowing one to determine the complex modulus. The temperature of the sample or the frequency of the stress are often varied, leading to variations in the complex modulus; this approach can be used to locate the glass transition temperature of the material, as well as to identify transitions corresponding to other molecular motions.
This course is intended to understand the engineering design of nuclear power plants using the basic principles of reactor physics, fluid flow and heat transfer. This course includes the following: Re
Introduction aux relations mise en œuvre-structures-propriétés des polymères, céramiques et métaux, fournissant les bases nécessaires à la sélection de matériaux et procédés pour la fabrication de com
The student has a basic understanding of the physical and physicochemical principles which result from the chainlike structure of synthetic macromolecules. The student can predict major characteristic
Explores thermal analysis techniques like TGA, DTA, and DFC, used for studying material properties and phase changes.
Covers fundamental characterization approaches for solid materials, focusing on elemental analysis, thermal analysis, microscopy, and neutron-based spectroscopies.
Explores electro-thermo-mechanical systems in micro and nanosystems, covering thermal bimorphs, material properties, actuators, and multiphysics simulations.
The production of radioisotope beams at the ISOLDE (Isotope Separator OnLine DEvice) facility at CERN is achieved by irradiating target materials (e.g. uranium carbides and metal foils) with protons.
The fast-ion phase-space coverage of the ASDEX Upgrade Fast-Ion Loss Detectors (FILD) has been estimated and the results are presented here. To that end, a numerical tool has been developed to determi
Synthesis gas, composed of H-2 and CO, is an important fuel which serves as feedstock for industrially relevant processes, such as methanol or ammonia synthesis. The efficiency of these reactions depe