Drill bit | EPFL Graph Search

Drill bits are cutting tools used in a drill to remove material to create holes, almost always of circular cross-section. Drill bits come in many sizes and shapes and can create different kinds of holes in many different materials. In order to create holes drill bits are usually attached to a drill, which powers them to cut through the workpiece, typically by rotation. The drill will grasp the upper end of a bit called the shank in the chuck. Drills come in standardized drill bit sizes. A comprehensive drill bit and tap size chart lists metric and imperial sized drills alongside the required screw tap sizes. There are also certain specialized drill bits that can create holes with a non-circular cross-section. Characteristics Drill bit sizes Drill geometry has several characteristics:

The spiral (or rate of twist) in the drill bit controls the rate of chip removal. A fast spiral (high twist rate or "compact flute") drill bit is used in high feed rate applications unde

Cutting Force Modelling for Drilling of Fiber-Reinforced Composites

Mihai-Bogdan Lazar

Although used in a very large variety of applications, drilling is one of the most complex and least understood manufacturing processes. Most of the research on drilling was done in the field of metal cutting for mechanical parts since, in this case, high precision and quality are needed. The use of composite materials in engineering applications has increased in recent years, and in many of these applications drilling is one of the most critical stages in the manufacturing process. This is because it is among the last operations in the manufacturing plan of composite parts. Delamination and extensive tool wear are among the problems which drilling of composite materials are currently facing. A major difference between metallic and composite plates is their structure: isotropic for metals and anisotropic for composite materials; meaning that while for metallic materials all the structure will respond in a similar manner under the machining loads, the composite structure will have localized responses from the same loads, leading to defects in the internal structure of the remaining work-piece material (i.e. delamination). Delamination can lead to failure in use and parts with such defects are usually discarded. Delamination is not usually visually detectable and special testing is necessary, affecting the costs of the final parts. Delamination during drilling was found to occur at tool entry (peel-up) or tool exit (push-out) and depends on the loads at inter-laminar level. The work presented in the current thesis focuses in providing reliable information about the thrust and torque distribution along the drill radius (and work-piece thickness) during drilling for varying cutting parameters, drill geometry and work-piece material. Such data should assist in the development of delamination models capable of capturing the influence of the drill geometry and cutting parameters on delamination onset and propagation during both exit and entry of the drill in the work-piece. A cutting force model is proposed to obtain the elementary cutting force distribution along the drill radius which is able to account for changes in axial feed rate and drill geometry. Based on oblique cutting, forces are considered on both rake and relief faces. A generic relationship in the form of a transformation matrix is developed to relate oblique cutting to drilling, valid for any drill geometry. The mathematical description of the drill geometry in the scope of cutting force modeling has been revised. The kinematics of the drilling process is now taken into account for (i) all geometrical parameters of the drill and for (ii) the elementary cutting forces decomposition. Additionally, a new drill type and its geometric features have been described mathematically and the definition of the geometrical parameters has been generalized so that other drills types or variations could be easily implemented into the model. It proved therefore possible to adopt simpler expressions for the empirical force coefficients of the cutting force model. Up to four empirical coefficients are used, which are calculated from experiments for each work-piece material and drill type. Most experimental investigations on drilling fiber reinforced composites analyze only the total thrust and torque generated during drilling or separately the forces caused by the chisel edge and cutting lips by drilling with or without a pilot hole. The later type of analysis suggested that is possible to obtain more detailed information about the distribution of the loads in drilling from the analysis of the forces variation during tool entry into the work-piece. Pursuing this direction, an experimental analysis method is proposed to obtain the axial and tangential elementary cutting force distribution along the tool radius or work-piece thickness. The cutting force distribution obtained experimentally was used to calibrate the cutting force model, rather than the total thrust and torque. The experimentally obtained cutting force distribution can also be used alone for analyzing the drilling process (i.e. the loads distribution among the plies of the composite laminate and how this load is influenced by changes in the drill geometry and the cutting conditions).

EPFL2012

Mechanical load distribution along the main cutting edges in drilling

Mihai-Bogdan Lazar, Paul Xirouchakis

Used in a very large variety of applications, drilling is one of the most complex manufacturing processes. Most of the research on drilling was done in the field of metal cutting since, in this case, high precision and quality are needed. The use of composite materials in engineering applications has increased in recent years, and in many of these applications drilling is one of the most critical stages in the manufacturing process. Delamination and extensive tool wear, affecting the quality and the costs, are among the problems which drilling of composite materials are currently facing. Understanding and predicting the cutting forces occurring during drilling of such materials would allow extending the currently used optimization methods and proposing new tool geometries and tool materials. The current paper introduces a new mechanistic model for predicting the cutting force distribution along the cutting edges of a drill. A simple, generic and effective method is proposed to relate drilling to oblique cutting using a direction cosine transformation matrix valid for any drill geometry. The oblique cutting model used considers forces on both rake and relief faces, and a simple system of empirical coefficients (their number is significantly less than other similar models). The empirical coefficients are calculated assuming the work-piece material is isotropic. The model is validated on experiments carried out on carbon-fiber and glass-fiber reinforced composites using two different drill types (tapered drill reamer and 2-facet twist drill), which are described in more detail in a previous published paper. The mathematical expression of the drill geometry is also reviewed; removing certain assumption, generalizing some definitions and introducing new drill geometry and features.

Elsevier2013

Augmented-reality-assisted timber drilling with smart retrofitted tools

Julien Gamerro, Andrea Settimi, Yves Weinand

An ordinary electric drill was integrated into a context-aware augmented reality (AR) framework to assist in timber-drilling tasks. This study is a preliminary evaluation to detail technical challenges, potential bottlenecks, and accuracy of the proposed object- and tool-aware AR-assisted fabrication systems. In the designed workflow, computer vision tools and sensors are used to implement an inside-out tracking technique for retrofitted drills based on a reverse engineering approach. The approach allows workers to perform complex drilling angle operations according to computer-processed feedback instead of drawing, marking, or jigs. First, the developed methodology was presented, and its various devices and functioning phases were detailed. Second, this first proof of concept was evaluated by experimentally scanning produced drillings and comparing the discrepancies with their respective three-dimensional execution models. This study outlined improvements in the proposed tool-aware fabrication process and clarified the potential role of augmented carpentry in the digital fabrication landscape.

2022

Cutting Force Modelling for Drilling of Fiber-Reinforced Composites

Mihai-Bogdan Lazar

EPFL2012