Boundary scan is a method for testing interconnects (wire lines) on printed circuit boards or sub-blocks inside an integrated circuit. Boundary scan is also widely used as a debugging method to watch integrated circuit pin states, measure voltage, or analyze sub-blocks inside an integrated circuit.
The Joint Test Action Group (JTAG) developed a specification for boundary scan testing that was standardized in 1990 as the IEEE Std. 1149.1-1990. In 1994, a supplement that contains a description of the Boundary Scan Description Language (BSDL) was added which describes the boundary-scan logic content of IEEE Std 1149.1 compliant devices. Since then, this standard has been adopted by electronic device companies all over the world. Boundary scan is now mostly synonymous with JTAG.
The boundary scan architecture provides a means to test interconnects (including clusters of logic, memories, etc.) without using physical test probes; this involves the addition of at least one test cell that is connected to each pin of the device and that can selectively override the functionality of that pin. Each test cell may be programmed via the JTAG scan chain to drive a signal onto a pin and thus across an individual trace on the board; the cell at the destination of the board trace can then be read, verifying that the board trace properly connects the two pins. If the trace is shorted to another signal or if the trace is open, the correct signal value does not show up at the destination pin, indicating a fault.
To provide the boundary scan capability, IC vendors add additional logic to each of their devices, including scan cells for each of the external traces. These cells are then connected together to form the external boundary scan shift register (BSR), and combined with JTAG Test Access Port (TAP) controller support comprising four (or sometimes more) additional pins plus control circuitry.
Some TAP controllers support scan chains between on-chip logical design blocks, with JTAG instructions which operate on those internal scan chains instead of the BSR.
Cette page est générée automatiquement et peut contenir des informations qui ne sont pas correctes, complètes, à jour ou pertinentes par rapport à votre recherche. Il en va de même pour toutes les autres pages de ce site. Veillez à vérifier les informations auprès des sources officielles de l'EPFL.
Boundary scan is a method for testing interconnects (wire lines) on printed circuit boards or sub-blocks inside an integrated circuit. Boundary scan is also widely used as a debugging method to watch integrated circuit pin states, measure voltage, or analyze sub-blocks inside an integrated circuit. The Joint Test Action Group (JTAG) developed a specification for boundary scan testing that was standardized in 1990 as the IEEE Std. 1149.1-1990.
Le JTAG (pour Joint Test Action Group) est le nom de la norme IEEE 1149.1 intitulée « Standard Test Access Port and Boundary-Scan Architecture », qui été normalisée en 1990. Le terme JTAG, désignant le groupe de travail qui a conçu la norme, est abusivement (mais très largement) utilisé au lieu du terme générique Boundary Scan, ou du sigle TAP (Test Access Port, port d'accès de test). La technique de boundary scan (littéralement, « scrutation des frontières ») est conçue pour faciliter et automatiser le test des cartes électroniques numériques.
La CAO électronique (pour Conception assistée par ordinateur électronique), nommée également en anglais EDA (pour Electronic design automation), est la catégorie des outils servant à la conception et la production des systèmes électroniques allant des circuits imprimés jusqu'aux circuits intégrés. Le terme CAO est aussi utilisé pour désigner la CAO mécanique, la conception assistée par ordinateur et la fabrication assistée par ordinateur en électronique et en électrotechnique.
Test of VLSI Systems covers theoretical knowledge related to the major algorithms used in VLSI test, and design for test techniques. Basic knowledge related to computer-aided design for test technique
Explore les techniques de conception pour la testabilité dans les systèmes VLSI, couvrant les méthodes ad hoc et structurées, la conception de numérisation et les normes de test modernes.
Explore les techniques de test pour les systèmes VLSI numériques, couvrant la modélisation des défauts, la génération de modèles de test et la conception pour la testabilité.